2007 Chevrolet Uplander Lt Mini Passenger Van 4-door 3.9l on 2040-cars

Auto blog

Amelia Island 2013: Chevrolet Corvette Sting Ray from concepts to split windows

While this year marks 60 years of the Chevrolet Corvette, the 2013 Amelia Island Concours d'Elegance focused on one of the coupe's most sought after models, the 1963 Sting Ray. General Motors design boss Ed Welburn was on hand to show off the all-new C7 Corvette, but even the hard-edged styling of the 2014 Stingray couldn't take away from the beautiful 1963 models sitting out on the field.
In addition to the original Sting Ray and the 1959 Sting Ray Concept, some of the other classic 'Vettes included "Big Tank" racecars, an interesting cutaway coupe, a right-hand-drive Z06 and the attention-grabbing 1963 Corvette Rondine by Pininfarina. Another impressive Corvette was the 1964 Corvette XP-819 rear-engine prototype. Owner Mike Yager had the car finished as a driving chassis for this year's show, but promises the car will be back to its original glory in time for next year's event.

First 2014 Chevy Corvette Stingray spotted crashed in the wild

This restyled blue 2014 Chevrolet Corvette Stingray is wearing manufacturer plates, and it appears to be the same one seen around the internet in various pictures lately. This crash is likely not part of the Chevrolet testing regimen, however. Digital Corvettes forum member gpetry posted the shot with a note: "got this picture e-mailed from a friend in Arizona last week..." No circumstances are given, other than the incident occurred in the thick of a set of curvy roads, and the coupe ping-ponged off a guardrail and into the rock wall. Hopefully everyone involved in the incident walked away.
It may not be a pretty thing to see, a crashed sports car that's not even available for sale yet, but rest easy. Many pre-production cars are used for development and then unceremoniously crushed and scrapped, anyway. If that's the case here, that makes this wrecked 'Vette less of a tragedy and more of a case of exceptional efficiency.

Chevy's 6.6-liter Duramax is pretty much all new

To say there's a heated battle in heavy-duty pickups is an understatement, with Chevrolet, Ford, and Ram constantly trading blows of increased torque, horsepower, and towing capacity. The latest salvo is the revised, more powerful turbo diesel 6.6-liter Duramax V8 in the 2017 Chevy Silverado. It has 910 pound-feet of torque, an increase of 145, putting it nearly level with the Ford Super Duty. Here's a closer look at where those gains come from. How exactly did Chevrolet add all that torque plus 48 horsepower? The automaker essentially took a fine-tooth comb to the entire engine. Chevy says it changed 90 percent of the V8, and the cumulative effect of those small changes adds up to big increases. As you might guess, the turbocharger is updated. The larger unit features electric actuation of the variable nozzle turbine (VNT), and what Chevy calls a double axle cartridge mechanism that separates the VNT moving parts from the housing. That helps with heat performance as well, with a claim that the exhaust side of the turbo can run continuously up to 1,436 degrees Fahrenheit. Helping that cause are six exhaust gaskets made of Inconel - an nickel alloy that contains chromium and iron – and upgraded stainless steel for the exhaust manifold. Despite having the same cast iron cylinder block, albeit with some minor enhancements, the engine has new cylinder heads, pistons, piston pins, connecting rods, and crankshaft, which have all been upgraded to handle 20 percent higher cylinder pressures. Alongside the increase in pressure, Chevrolet also increased the cylinder head's structure with a honeycomb design. The pattern features high-strength aluminum with dual layer water jackets that not only improve strength, but also optimize water flow for better cooling. For 2017, the cylinder head also benefits from integrated plenum that aids the engine in getting more air under heavy loads. The cylinder head isn't the only component to get a minor update, as the pistons have a larger diameter pin for improved oil flow. The same detailed improvements has been bestowed to the humble connecting rods (second in our hearts only to the inanimate carbon rod). The new design has the bolts oriented roughly 45-degrees to the rod instead of parallel. The angle split design, as it's called allows for easier passage through the cylinder.