2006 Chevrolet Trailblazer Ss on 2040-cars

Auto blog

Corvette Z06 and Viper TA square off at the strip

There are many long-standing grudge matches among automobiles: 911 vs GT-R, Mustang vs Camaro, Ferrari vs Lamborghini... but as far as high-end American metal goes, it doesn't get much more legendary than Viper vs 'Vette. So after Chevy released the new Corvette Z06, we knew it was only a matter of time before it would have to square off against the Viper TA. And what better place to pit these two parallel pillars of American performance than on the drag strip? Fortunately that's just what we have here. In one corner, the 2014 Dodge Viper TA, with its 8.4-liter V10 pumping out 640 horsepower and 600 pound-feet of torque. In the other, the 2015 Chevrolet Corvette Z06, the supercharger on its 6.2-liter V8 more than making up for the discrepancy in displacement and cylinder count to produce 650 hp and just as much torque. But numbers don't tell the whole story, so watch the video clip to see which reaches the end of the quarter-mile first. News Source: To the Floor via YouTubeTip: James Chevrolet Dodge Videos drag race chevy corvette z06 quarter mile drag strip srt viper ta

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Even if GM does close all 5 of those plants, it'll still have too many

DETROIT — General Motors' monumental announcement on Monday that it will close three car assembly plants and two powertrain plants in North America and slash its workforce will only partially close the gap between capacity and demand for the automaker's sedans, according to a Reuters analysis of industry production and capacity data. Sales of traditional passenger cars in North America have been declining for the past six years and are still withering. After GM ends production next year at factories in Michigan, Ohio and Ontario, it will still have four U.S. passenger-car plants — all operating at less than 50 percent of rated capacity, according to figures supplied by LMC Automotive. In comparison, Detroit-based rivals Ford and Fiat Chrysler Automobiles will have one car plant each in North America after 2019. The Detroit Three are facing rapidly dwindling demand for traditional passenger cars from U.S. consumers, many of whom have shifted to crossovers and trucks. Passenger cars accounted for 48 percent of retail light-vehicle sales in the United States in 2014, according to market researchers at J.D. Power and Associates. This year, sedans will account for less than a third of light vehicle sales. That shift in turn has left most North American car plants operating far below their rated capacities, while many SUV and truck plants are running on overtime. The collapse in passenger-car demand is a challenge for nearly all automakers in the United States, including Japan's Toyota and Honda, which have the top-selling models in the compact and midsize car segments. Toyota executives said last month they are evaluating the company's U.S. model lineup. But Toyota also plans to build compact Corolla sedans at a new $1.6 billion factory it is building in Alabama with partner Mazda. The obstacles facing GM in its plans to close more auto factories became apparent on Tuesday as U.S. President Donald Trump threatened to block payment of government electric vehicle subsidies to GM. While it is not certain that Trump unilaterally has the power to do that, he made it clear he intends to use his office to pressure the company to keep open a small car plant in Ohio that GM says will stop building vehicles in March.