2003 Chevy Tahoe Lt on 2040-cars

Auto blog

Final C6 Corvette built in Bowling Green

With all of the attention given to the 2014 Chevrolet Corvette Stingray lately, you could be forgiven for thinking that it's already well along in production, yet tooling up for the new C7 has only just begun. In fact, production of the outgoing C6 generation in Bowling Green, Kentucky just halted on Thursday.
As the C6 has aged, production numbers have predictably ebbed along with demand, but this year, the addition of the 427 and 60th anniversary models resulted in an uptick in vehicles built - this, despite a model year shortened by around 25 percent to accomodate the new model changeover. The final C6 Corvette ever, No. 13,466 built this year, was a white 427 Convertible destined for the General Motors Heritage Center museum. The car's 7.0-liter V8 heart was assembled by Corvette chief engineer Tadge Juechter himself.
In total, Bowling Green pushed out 215,100 C6 Corvettes over nine years. If you're still a C6 fan at heart and are hoping to get a good deal on a phase-out model, step lively - Chevrolet reportedly had about 6,100 unsold units, which Autoweek suggests is good for around five and a half months of supply at the model's current sales rates. Given that demand will likely slacken even further as the C7 draws closer, that should be a big enough stockpile to keep dealers satisfied until 2014 Stingrays begin showing up on their forecourts in December.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Diesel Power finds the ultimate modified oil-burner

For nine years, Diesel Power magazine has run the Diesel Power Challenge, this year's grindfest being "a week-long torture test that features seven events, nine trucks, 8,000 horsepower, and nearly 15,000 pound-feet of torque." The road to being crowned "the most powerful truck" starts with a dyno run, and then continues through the completion of a CDL-style obstacle course, an eighth-of-a-mile drag race while towing a 10,000-pound trailer, a quarter-mile drag race without a trailer, a fuel economy test in the mountains and finally a sled-pulling test through a 300-foot-long packed-mud pit.
What kind of trucks get into such a fight? Last year's winner, for instance - who upgraded his truck this year to prove he didn't "luck into the win" - drives a 2008 Ford F-250 Super Duty with a 6.4-liter Power Stroke V8 upgraded with a custom intake, Elite Diesel triple turbos and a two-stage nitrous system. Another competitor has a 2005 Dodge Ram 2500 powered by a 5.9-liter Cummins inline-six, upgraded with Garrett turbos, dual-stage nitrous, a seven-inch exhaust stack and twin fans built into the bed to cool the Sun Coast Omega transmission. The numbers on that truck: 1,255 horsepower, and 2,063 pound-feet of torque at the wheels. Naturally, as the image above might suggest, things don't always end well.
You'll find all five videos covering this years challenge below. A scene in the dyno video sums it all up perfectly: a competitor leaves his nitrous on too long and the crew is treated to some ominous poppings, he leans out the window, throws both hands up and shouts, "Amer'ca!"