2015 Chevrolet Suburban 1500 Lt on 2040-cars

Auto blog

Opel's own ad shows Ampera-e beating Opels in drag race

The Opel Ampera-e isn't expected to set any world records on a quarter-mile drag strip. But when it comes to crossing a major boulevard, though, the European version of the Chevrolet Bolt electric vehicle will more than hold its own, potentially scaring inattentive pedestrians everywhere. According to a 35-second video posted by General Motors' Opel division, at least. Opel set up the Ampera-e against four other small-and-sporty vehicles, including racing versions of the Opel Adam and Opel Astra as well as stock versions of the Opel Insignia and Corsa (what, you expected a Corvette to be in there?). With the EV's off-the-line torque as a selling point, Opel showed the Ampera-e beating the other vehicles in a 30-meter (100-foot) drag race. Of course, the video also shows the EV getting passed by some of the others soon after, but the point was made. Opel doubled down by adding the tagline "Fun to Drive" at the end of the video. While Opel hasn't revealed the single-charge range of the Ampera-e, it should be roughly the same as the Chevrolet Bolt, which will be about 200 miles. In addition, the Ampera-e, like the Bolt in the US, will get 200 horsepower from its electric motor, and will be able to go from 0 to 60 miles per hour in less than seven seconds. The Ampera-e will debut at the 2016 Paris Motor Show later this month. General Motors said in February that Europe would get the Ampera-e by next year. Opel had previously used the Ampera name with the Euro version of the Chevrolet Volt extended-range plug-in. Related Video: News Source: Opel/YouTube via Green Car Reports Green Chevrolet GM Opel Electric opel ampera-e ampera-e

Nissan Frontier and a mid-engine Mustang | Autoblog Podcast #622

In this week's Autoblog Podcast, Editor-in-Chief Greg Migliore is joined by News Editor Joel Stocksdale and Associate Editor Byron Hurd. They discuss news about the 2020 and 2021 Nissan Frontier, as well as a mystery Mustang and classic luxury coupes. After that, they talk about cars from the fleet including Chevy Silverados and the long-term Volvo S60 T8. Autoblog Podcast #622 Get The Podcast iTunes – Subscribe to the Autoblog Podcast in iTunes RSS – Add the Autoblog Podcast feed to your RSS aggregator MP3 – Download the MP3 directly Rundown 2020 and 2021 Nissan Frontier updates 1966 mid-engine Mustang prototype Personal luxury coupes Cars we're driving 2020 Chevy Silverado 1500 Trail Boss 2020 Chevy Silverado 2500 HD 2020 Volvo S60 T8 plug-in hybrid Feedback Email – Podcast@Autoblog.com Review the show on iTunes Related Video:

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck