2014 Chevrolet Silverado 3500 Ltz H/d on 2040-cars

Auto blog

Thanks for keeping us on our toes, Detroit Auto Show [w/poll]

Here at Autoblog, we love unexpected debuts at auto shows – and judging by our Detroit Auto Show comments and traffic, you do, too. Surprise reveals have been fewer and farther between in recent years with so many ways for vehicles to be teased or leak out, but this week's show has been a revelation. More to the point, it's been a series of revelations, with automakers from around the globe successfully delivering a brace of concept and production surprises. It's made our jobs a lot more exciting and challenging this week, and even though it's actually more work to react and run-and-gun when the sheet is pulled on a surprise reveal than it is to publish an already-written embargoed story, we've had more fun covering this show for you than any domestic show in memory. We hope you've enjoyed the surprises along with us. To that end, borrowing the words of an unnamed automaker PR flack, we'd like to thank the following automakers for enduring "mountain of antacids" and that "creeping sense of paranoia" necessary to keeping ones' wares totally under wraps until the sheets are pulled off the sheetmetal: Buick Avenir concept Chevrolet Bolt concept Ford GT concept Ford Mustang Shelby GT350R Ford F-150 SVT Raptor Hyundai HCD-15 Santa Cruz concept And while we're at it, we'd like to throw in an shout-out to Detroit's substantially revised and revitalized Cobo Center, and in particular, the redone Michelin media center, which is arguably the single best accommodations for writing show stories that we've encountered on the entire international circuit. Well done, everyone. Thank you, and keep the surprises coming. Auto News Detroit Auto Show Buick Chevrolet Ford Hyundai Volvo 2015 Detroit Auto Show

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Why does the Corvette Stingray have so many vents? Here's why

Just looking at the new 2014 Chevrolet Corvette Stingray, it's not hard to see that the car's design was created with aerodynamics at the forefront, but Chevrolet designers point out exactly what went into designing the iconic coupe in a pair of recently released videos. The videos show the Corvette going through early design phases, including clay models and wind tunnel tests, as well as talking to the car's chief engineer, Tadge Juechter.
Both videos help explain various aspects of the C7 Corvette, but it's the aero tuning of the car that is most interesting. This includes extra attention paid to the lower air dam and vented hood to help reduce drag and lift, while the rear quarter inlets are for differential and transmission cooling. Juechter said that some of these aero-tuned elements were inspired from GM's involvement in racing.
If you have about five minutes and you can't get enough information about the new 'Vette, then check out the videos posted below.