2005 Chevrolet Silverado 3500 Lt Crew Cab Pickup 4-door 6.6l on 2040-cars

Auto blog

GM recalls 8,500 Chevrolet Malibu models for rear suspension glitch

According to a letter from General Motors to the National Highway Traffic Safety Administration, flaws in the build process of the 2013 Chevrolet Malibu have led to the recall of 8,519 cars. Units built between December 6, 2011 and January 15, 2013 may have been assembled with rear suspension cradles that had insufficient torque applied to certain bolts. That out-of-spec assembly could lead to issues ranging from slight noises to a loss of vehicle control.
The problem was first noticed in December of last year by a GM test fleet driver and eventually tracked back to the improperly torqued bolts on the suspension cradle assembled through July 2012 by a supplier located not too far from the Malibu's Detroit/Hamtramck Assembly Plant. Since an official NHTSA recall notice has not been issued yet, it isn't clear whether or not Detroit-built Malibus were the only ones affected (the 2013 Malibu is also built at GM's Fairfax Assembly Plant in Kansas City, Kansas). Dealers will fix the problem by inspecting vehicles for proper torque specs, retightening if not within specs and, in some cases, perform a rear-wheel alignment.

GM recalling 686k Lambda-platform models for hatch repair

General Motors is recalling 686,287 units of its Lambda platform crossovers. On models equipped with a power rear hatch the system can potentially fail. This campaign includes the 2008-2012 Buick Enclave, 2009-2012 Chevrolet Traverse, 2007-2012 GMC Acadia, and 2007-2010 Saturn Outlook. According to GM's documents to the National Highway Traffic Safety Administration (as a PDF), dirt can get into a portion of the strut that holds up the hatch and cause the part to prematurely fail. There's a redundancy in place called the Prop Rod Recovery system that's designed to shut the liftgate if there's a malfunction. However, if the breakdown happens too quickly after the hatch is opened the prop rod might not work the way it's supposed to. If someone were in the way of the falling liftgate, they could be hurt. For the repair, dealers will update the software for the power liftgate actuator motor control unit to prevent the hatch from closing so quickly. They'll also check the operation of the system afterward. Related Video: RECALL Subject : Liftgate Struts may Fail and Liftgate may Fall Report Receipt Date: JUN 30, 2015 NHTSA Campaign Number: 15V415000 Component(s): STRUCTURE Potential Number of Units Affected: 686,287 All Products Associated with this Recall Vehicle Make Model Model Year(s) BUICK ENCLAVE 2008-2012 CHEVROLET TRAVERSE 2009-2012 GMC ACADIA 2007-2012 SATURN OUTLOOK 2007-2010 Details Manufacturer: General Motors LLC SUMMARY: General Motors LLC (GM) is recalling certain model year 2008-2012 Buick Enclave vehicles manufactured January 3, 2007, to February 29, 2012, 2009-2012 Chevrolet Traverse vehicles manufactured July 6, 2008, to February 29, 2012, 2007-2012 GMC Acadia vehicles manufactured September 15, 2006, to February 29, 2012, and 2007-2010 Saturn Outlook vehicles manufactured August 17, 2006, to March 18, 2010. The affected vehicles, equipped with the power liftgate option, have gas struts that hold the power liftgate up when open. These struts may prematurely wear and the open liftgate may suddenly fall. CONSEQUENCE: If the open liftgate unexpectedly falls, it may strike a person, increasing their risk of injury. REMEDY: GM will notify owners, and dealers will update the software for the power liftgate actuator motor control unit so that the motor will prevent the rapid closing of the lift gate, free of charge. The manufacturer has not yet provided a notification schedule.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck