2003 Chevrolet Silverado 2500 Hd Ls Crew Cab Pickup 4-door 6.0l on 2040-cars

Auto blog

Junkyard Gem: 1986 Chevrolet Sprint Plus

General Motors sold second- and third-generation Suzuki Cultuses with Geo or Chevrolet Metro badging in the United States from 1989 through 2001 model years, and we've all seen plenty of those cars on the street over the years. The first-generation Cultus was sold here as well, with Chevrolet Sprint badges, and I've found a rare example of the Sprint five-door hatchback in a Northern California car graveyard. The Chevy Sprint first appeared on the West Coast as a 1985 model, then became available everywhere in the United States for the 1986 through 1988 model years (in Canada, it was sold as the Pontiac Firefly). It was available here as a hatchback with three or five doors; for 1986 only, the five-door was badged as the Sprint Plus. Soon enough, The General would be selling many more Asian-built cars with Detroit badges here. Isuzu I-Marks were sold as Chevrolet/Geo Spectrums starting in the 1986 model year, while Daewoo provided the Pontiac LeMans two years later. Under the hood, a 1.0-liter three-cylinder rated at 48 horsepower. The five-door Sprint cost $5,580 in 1986, which was $200 more than the three-door (those prices would be $15,445 and $14,891 in 2023 dollars). I've documented seven discarded Sprints prior to this one (including an extremely rare Turbo Sprint), and all of them were three-doors; we can assume that price was the most important factor for Sprint buyers. Gasoline prices were crashing hard during the middle 1980s, but memories of gas lines and odd-even-day fuel rationing from 1979 remained strong. What cars competed with the '86 Sprint on sticker price? Well, there was no way to undercut the hilariously affordable (and terrible) Yugo GV, which cost $3,990. The much bigger (but still pretty bad) Hyundai Excel listed at $4,995, while Toyota would sell you a sturdy (but zero-fun) Tercel starting at $5,448. Even the wretched Chevy Chevette — yes, it was still available in 1986 — cost $5,645. The original buyer of this car was willing to shell out an extra $395 to get an automatic instead of the base five-speed manual. That's about $1,093 in today's money. This car must have been slow. By the end, the doors were held shut with duct tape, but it still stayed alive until age 37. 53 miles per gallon on the highway! It does everything. The camels of the highway.

Chevy's 6.6-liter Duramax is pretty much all new

To say there's a heated battle in heavy-duty pickups is an understatement, with Chevrolet, Ford, and Ram constantly trading blows of increased torque, horsepower, and towing capacity. The latest salvo is the revised, more powerful turbo diesel 6.6-liter Duramax V8 in the 2017 Chevy Silverado. It has 910 pound-feet of torque, an increase of 145, putting it nearly level with the Ford Super Duty. Here's a closer look at where those gains come from. How exactly did Chevrolet add all that torque plus 48 horsepower? The automaker essentially took a fine-tooth comb to the entire engine. Chevy says it changed 90 percent of the V8, and the cumulative effect of those small changes adds up to big increases. As you might guess, the turbocharger is updated. The larger unit features electric actuation of the variable nozzle turbine (VNT), and what Chevy calls a double axle cartridge mechanism that separates the VNT moving parts from the housing. That helps with heat performance as well, with a claim that the exhaust side of the turbo can run continuously up to 1,436 degrees Fahrenheit. Helping that cause are six exhaust gaskets made of Inconel - an nickel alloy that contains chromium and iron – and upgraded stainless steel for the exhaust manifold. Despite having the same cast iron cylinder block, albeit with some minor enhancements, the engine has new cylinder heads, pistons, piston pins, connecting rods, and crankshaft, which have all been upgraded to handle 20 percent higher cylinder pressures. Alongside the increase in pressure, Chevrolet also increased the cylinder head's structure with a honeycomb design. The pattern features high-strength aluminum with dual layer water jackets that not only improve strength, but also optimize water flow for better cooling. For 2017, the cylinder head also benefits from integrated plenum that aids the engine in getting more air under heavy loads. The cylinder head isn't the only component to get a minor update, as the pistons have a larger diameter pin for improved oil flow. The same detailed improvements has been bestowed to the humble connecting rods (second in our hearts only to the inanimate carbon rod). The new design has the bolts oriented roughly 45-degrees to the rod instead of parallel. The angle split design, as it's called allows for easier passage through the cylinder.

China's rise, global restructuring wither GM's Korea division

An article in the Daily Kanban suggests the sun is setting on GM Korea, and it could already be well into dusk. GM Korea came about when General Motors, along with co-investors SAIC and Suzuki, bought Daewoo Motors from parent company Daewoo Group in 2001; it had a previous tie-up with GM, a joint venture that ended in 1992, although Daewoo cars were based on GM cars until 1996. Over the decade following the purchase, it became such an important part of operations that it was renamed GM Korea in 2011, "to reflect its heightened status in [the] global operations of GM." Just two years later, the printed rumors were that the subsidiary responsible for a fifth of Chevrolet's global production could be shutting down. The division's sales were down almost 21 percent through November of last year, counting domestic South Korean sales, exports, and CKD – Complete Knock Down – products. That makes the labor strife, already an issue for four years, even more acute, reports say the subsidiary will lose $36 million a year if it can't get the job and wage cuts it wants, and government concessions can't make up for the losses. And it gets worse, so head over to Daily Kanban to read the rest of the story.