2011 Ltz Used Cpo Certified 5.3l V8 16v Automatic Bose Onstar on 2040-cars

Auto blog

IIHS: High numbers of drivers treat partially automated cars as fully self-driving

WASHINGTON — Drivers using advanced driver assistance systems like Tesla Autopilot or General Motors Super Cruise often treat their vehicles as fully self-driving despite warnings, a new study has found. The Insurance Institute for Highway Safety (IIHS), an industry funded group that prods automakers to make safer vehicles, said on Tuesday a survey found regular users of Super Cruise, Nissan/Infiniti ProPILOT Assist and Tesla Autopilot "said they were more likely to perform non-driving-related activities like eating or texting while using their partial automation systems than while driving unassisted." The IIHS study of 600 active users found 53% of Super Cruise, 42% of Autopilot and 12% of ProPILOT Assist owners "said that they were comfortable treating their vehicles as fully self-driving." About 40% of users of Autopilot and Super Cruise — two systems with lockout features for failing to pay attention — reported systems had at some point switched off while they were driving and would not reactivate. "The big-picture message here is that the early adopters of these systems still have a poor understanding of the technologyÂ’s limits," said IIHS President David Harkey. The study comes as the National Highway Traffic Safety Administration (NHTSA) is scrutinizing Autopilot crashes. Since 2016, the NHTSA has opened 37 special investigations involving 18 deaths in crashes involving Tesla vehicles and where systems like Autopilot were suspected of use. Tesla did not respond to requests for comment. Tesla says Autopilot does not make vehicles autonomous and is intended for use with a fully attentive driver who is prepared to take over. GM, which in August said owners could use Super Cruise on 400,000 miles (643,740 km) of North American roads and plans to offer Super Cruise on 22 models by the end of 2023, did not immediately comment. IIHS said advertisements for Super Cruise focus on hands-free capabilities while Autopilot evokes the name used in passenger airplanes and "implies TeslaÂ’s system is more capable than it really is." IIHS in contrast noted ProPILOT Assist "suggests that itÂ’s an assistance feature, rather than a replacement for the driver." NHTSA and automakers say none of the systems make vehicles autonomous. Nissan said its name "is clearly communicating ProPILOT Assist as a system to aid the driver, and it requires hands-on operation.

GM executive chief EV engineer says reducing cost of plug-in vehicles is 'huge priority'

As we know, another major automaker investing heavily in electrified vehicles is General Motors, and it's doing things much differently than rivals BMW, Ford or Nissan. The Chevrolet Volt extended-range EV is a modest seller at its $35,000 sticker price but a huge hit with owners. The Chevy Spark BEV, still in limited availability, puts smiley faces on its owners and drivers. The just-introduced Cadillac ELR, a sharp-looking, fun-driving $76,000 luxocoupe take on the Volt's EREV mechanicals, has admittedly low sales expectations. With this interesting trio in showrooms and much more in the works, the third vehicle electrification leader I collared for an interview at Detroit's North American International Auto Show (see #1 and #2) was Pam Fletcher, GM's executive chief engineer, Electrified Vehicles. ABG: Why do your EREVs need four-cylinder power to extend their range when BMW's i3 makes do with an optional 650 cc two-banger? "We designed [the Volt and the ELR] to go anywhere, any time" - Pam Fletcher PF: I get that question all the time: why not something smaller? You don't really need that much. You use the electric to its ability, then you just need to limp. But we designed those cars to go anywhere, any time, and we don't want their performance to be compromised. If you're driving through the mountains, we don't want you to be crawling up grades, or to be limited on any terrain. So it's optimized to be able to travel literally the biggest grades and mountain roads around the globe at posted speeds. Because what if you can't? Another good reason: when the engine is on, you have to run it wide open throttle, max speed, most of the time. And while we can do a lot with acoustics, and the ELR has active noise cancelation, a small-displacement, low cylinder-count engine at high speed, high load all the time isn't something you want to live with. That's how we came up with the balance we did among the key factors of performance, NVH [noise, vibration and harshness] and range. ABG: Where you go from here? Is the range-extender engine due for an update? PF: We know and love the current Volt, and there is still a lot of acclaim about it, so we think it's a good recipe. But we are heavily in the midst of engineering the next-generation car, which I think everyone will love and be excited about.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck