1957 Custom Step Side Chevy Pickup 3100 on 2040-cars

Auto blog

GM patent reveals new two-stage turbocharger

Modern turbochargers may be some of the best ever made, but performance is something that engineers are always trying to improve. According to GM Inside News, General Motors (GM) is hoping to alleviate some of the negative aspects of a two-stage turbocharger setup with a newly-patented design. The patent, that was filed on May 19, 2016, reveals a clever bypass system that allows the engine, a four-cylinder unit, to optimize both the low-pressure and high-pressure inlets for its respective functions. According to the filing, a conventional two-stage turbocharger setup is engineered to allow both turbines to operate simultaneously at low and mid engine speeds. At high engine speeds, only the low-pressure turbine works. The setup can't isolate either the low or high pressure side, which can impair low-end performance. GM's new two-stage turbocharger setup looks to eliminate this by linking the high-pressure turbo to the exhaust manifold through the high-pressure inlet duct. The low-pressure turbo is attached to the high-pressure turbo by a low-pressure inlet duct, which is linked to a connecting channel. A single actuator that is housed in the exhaust manifold creates a bypass that can opens the high-pressure inlet or close the connecting channel. Depending on what the engine load and speed is, the ECU guides the actuator—a single rotating spindle with discs corresponding to flanges on the high and low pressure sides—to isolate one of the two turbos. Isolating the turbos allow the respective inlets to be engineered for the best possible fluid dynamic performance. The setup should increase performance and decrease lag. There's no word on what car this setup will make an appearance on, but it will most likely be used in premium vehicles before trickling down to the rest of GM's vehicles. Related Video: News Source: GM Inside News, AutoGuide via GM Authority Cadillac Chevrolet GM Technology Sedan turbo patent engine turbocharging

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

2016 Chevy Colorado and GMC Canyon recalled for opening console lids

The Basics: General Motors is recalling 9,200 examples of the 2016 Chevrolet Colorado with build dates between August 25, 2015 and September 24, 2015, and the 2016 GMC Canyon manufactured from August 28, 2015 to September 24, 2015. In total, 8,763 of these pickups are in the US, and the rest are in Canada or Mexico. The Problem: The console compartment lid could open in a crash, and the items inside the storage compartment might hit occupants during the accident. This fault puts the pickups out of compliance with the Federal Motor Vehicle Safety Standard. Injuries/Deaths: None reported. The fix: Dealers will replace the console compartment door latch assembly with an improved part. If you own one: GM has not yet told NHTSA when the repairs for these pickups begin. Related Video: RECALL Subject : Console Door may not Fully Latch/FMVSS 201 Report Receipt Date: DEC 01, 2015 NHTSA Campaign Number: 15V807000 Component(s): LATCHES/LOCKS/LINKAGES Potential Number of Units Affected: 8,763 All Products Associated with this Recall Vehicle MakeModelModel Year(s) CHEVROLET COLORADO 2016 GMC CANYON 2016 Details Manufacturer: General Motors LLC SUMMARY: General Motors LLC (GM) is recalling certain model year 2016 Chevrolet Colorado trucks manufactured August 25, 2015 to September 24, 2015, and GMC Canyon trucks manufactured August 28, 2015 to September 24, 2015. The affected vehicles have a console compartment lid latch assembly that may fail to keep the compartment door closed in the event of a crash. As such, these vehicles fail to comply with the requirements of the Federal Motor Vehicle Safety Standard (FMVSS) number 201, "Occupant Protection in Interior Impact." CONSEQUENCE: If the console compartment door does not remain closed in a crash, the contents stored in the console may strike the vehicle occupants, increasing their risk of injury. REMEDY: GM will notify owners, and dealers will replace the console compartment door latch assembly, free of charge. The manufacturer has not yet provided a notification schedule. Owners may contact Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16370. NOTES: Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.