1987 Monte Carlo Ls 305 V8 36k Miles on 2040-cars

Auto blog

Want a V8 on the cheap? Buy a work truck

In case you didn't notice, V8 cars have gotten pretty expensive. If you want a modern muscle car like the Dodge Challenger R/T, Ford Mustang GT, or Chevy Camaro SS, you'll need between $34,000 and $38,000 for a stripped out example of one. The cheapest of those is the Challenger, and the priciest is the Camaro. These are also the cheapest V8 cars the companies offer. But if you absolutely have to have a V8 for less, there is an option, work trucks. As it turns out, all of the Big Three offer their most basic work trucks with V8s. And because they're so basic, they're pretty affordable, especially when sticking with the standard two-wheel drive. A Ram 1500 Tradesman with a V8 can be had for as little as $29,840, which is a little more than $4,000 less than a Challenger R/T. For a bit more at $30,275, you can have a Chevy Silverado W/T, almost $8,000 less than a Camaro SS. The most expensive is the V8 Ford F-150 starts at a starting price of $30,670, which is a bit over $5,000 less than the Mustang. Of course you'll be in an ultra bare bones vehicle with few comforts, and the price will go up if you add stuff, but we're bargain hunting here, and sacrifices are sometimes necessary. Besides, what you lose in comfort, you gain in loads of cargo space and towing (try to look at the bright side). Also, as a side note, all three trucks are available with optional electronic locking rear differentials. At the discounted price of these trucks, you still get a heaping helping of power. The most potent of the trio is the Ram 1500 Tradesman with 395 horsepower and 410 pound-feet of torque generated by a 5.7-liter V8. Compared with the Challenger R/T, the Ram is up by 20 horsepower and they're tied for torque. The value proposition is even more stark between the two vehicles when looking at the price per horsepower. Each pony in the Ram costs $75.54, while the Challenger charges you $90.91. The Challenger is also more expensive per horsepower than its close competitors. The F-150's 5.0-liter V8 is just barely behind the Ram with 395 horsepower and 400 pound-feet of torque. That's still more power than the Challenger, and it matches the torque of the 2017 Mustang GT. On the down side, it still would be down 20 horsepower on that same 2017 Mustang, and it's behind by 60 horsepower and 20 pound-feet on the new 2018 Mustang GT. The F-150 also just edges out the Mustang in the dollar per horsepower measure.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

NHTSA investigates 1.7 million GM SUVs for windshield wiper failures

WASHINGTON - The U.S. National Highway Traffic Safety Administration (NHTSA) said on Tuesday it is investigating whether General Motors should recall an additional 1.7 million sport utility vehicles due to an issue with windshield wiper failures. GM in August 2016 recalled 367,800 2013 GMC Terrain and Chevrolet Equinox SUVs in the United States to address the problem. But after receiving 249 complaints about similar problems, the federal agency said it is probing whether the recall should be expanded to include an additional 1.7 million vehicles from the 2010-2016 model years. The automaker said it is cooperating with the NHTSA review. GM said it recalled the 2013 GMC Terrain and Chevrolet Equinox SUVs "because warranty data showed a higher-than-expected failure rate," adding it has continued to monitor field data on other model years of those vehicles. GM noted that no crashes or injuries related to the issue have been reported. The Detroit-based automaker said the recalls were prompted after a GM Canada brand quality manager reported a potential safety issue relating to reports of windshield wiper failures in Canada through GM's "Speak Up For Safety," program in late 2015. The data showed significantly higher field incidents in parts of Canada, which prompted a June 2016 recall there. Over the next two months, a higher number of U.S. reports prompted a U.S. recall, the company added. In the 2016 recall, GM said the front-wiper module would be replaced with a module that has a water deflector and, if needed, dealers would fill the water management hole and drill a new small hole in a different location.(Reporting by David Shepardson, editing by G Crosse)Related Video: Government/Legal Recalls Chevrolet GM GMC SUV