1994 Chevrolet Impala Ss Sedan 4-door 5.7l on 2040-cars

Auto blog

This 450-hp electric Lotus Evora is powered by Tesla and Chevrolet

When someone mentions an electric Lotus, the first thing that comes to mind is the Tesla Roadster, the California-based automaker's first vehicle. That car started life as an Elise before being heavily massaged and adapted by Tesla's engineers. In a similar spirit, the people at Onpoint Dyno are close to finishing Blue Lightning, a track-ready all-electric Lotus Evora. Blue Lightning uses a Tesla drive unit and a Chevrolet Volt battery pack, both mounted in the middle in place of the Evora's 3.5-liter Toyota V6. It's putting down about 450 horsepower at the wheels. The car was built for time attack sessions, so power is fed through custom forged wheels and super sticky Pirelli PZero Trofeo R tires, the same ones found on the last Chevrolet Camaro Z/28. There is a custom digital instrument cluster in place of the Lotus gauges. There's also a regen paddle on the left side of the steering wheel. With a full charge, Blue Lighting should go about 120 miles. While the car runs under its own power, it's only about 90 percent complete. It has no power steering, no firewall in between the seats and the motor and battery pack, no A/C, and a large hole where the shift lever used to be. Other final touches include fine-tuning the brakes and suspension. There is also a custom rear bumper coming that should make it look more like the new Lotus Evora 400. Onpoint Dyno expects the car to hit the track in the next month or so. Related Video:

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

First 2015 Chevy Corvette Z06 engine blows up at just 891 miles

You've waited and watched and waited some more for the arrival of your 650-horsepower, $78,000 Chevrolet Corvette Z06. Finally, that joyous day arrives and you eagerly, but gingerly, begin to break-in the 6.2-liter supercharged V8 monster under your hood. Then 900-odd miles after delivery, your excitement grinds, quite literally, to a halt. That's what the owner of one 2015 Z06 claimed happened to him when a simple break-in drive resulted in a lunched engine. The owner, known as Lawdogg149 on Corvette Forum, says he was out breaking-in his car ahead of a January track event when it happened. "While making a pull from 35 miles per hour, I accelerated and shifted short of redline, and boom - the car began knocking. I pulled over and popped the hood. I could hear a loud knock coming from the No. 6 cylinder area along with a serious, grinding, metal-on-metal sound coming from the supercharger area," Lawdogg wrote. A subsequent trip to the dealer confirmed his concerns, with the service facility telling Lawdogg that the No. 6 valvetrain had failed. The dealer couldn't research the issue further, though, as General Motors requested the engine be returned for a more thorough evaluation. The good news for the Z06's unlucky owner, at least, is that GM will be covering the engine replacement under warranty, an expense that Corvette Forum estimates is a nearly $24,000 procedure. At this point, the two leading theories behind the engine's detonation involve a manufacturing defect – which could be why GM is so keen to tear the blown powerplant down – or a mistake on the part of Lawdogg. As Motor Authority points out, such an error could be something as simple as the Z06's owner accidentally shifting to first rather than third during his 35-mph pull. If, however, there's a deeper manufacturing problem with the Z06's engine, this might not be the only case we end up hearing about.