1963 Chev Impala Air Ride Staggered Wheels Billet Specialties V Kit Accuair on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Meet the mother-daughter team that's worked on almost every Chevy Volt

It's Mother's Day, and we're soft enough we love our mothers enough to share a new video from General Motors with you. In it, we meet Monique Watson (left) and Evetta Osbourne, a mother-daughter team that works at the Detroit-Hamtramck Assembly where GM makes the Chevy Volt (along with all of GM's other plug-in hybrids: the Opel Ampera, Holden Volt and Cadillac ELR). The two work side-by-side and have installed the lithium-ion battery pack on almost all of those vehicles - nearly 80,000 of them - since GM started making the pre-production Volts in 2009. In a prepared statement, Watson said that she likes working next to her mom, day in and day out, and they the two are totally in sync when it comes to putting the 400-pound, 16.5-kWh packs into the vehicle undersides. They two can also share stories throughout the day, and Watson said, "The arrangement has absolutely improved our relationship." Osborne started working at Detroit-Hamtramck in 1999, Watson since 2006. If you're driving a Volt today, you probably have them to thank for doing a bit of the work putting your car together. See a short video of them in action below. It's Always Mother's Day for Detroit-Hamtramck Duo Mother, daughter install lithium-ion battery pack in nearly all GM electric vehicles 2014-05-08 DETROIT – For Detroit resident Evetta Osborne, every day is Mother's Day. That's because she literally works side by side with her daughter, Monique Watson, at General Motors' Detroit-Hamtramck assembly plant. They have installed the lithium-ion battery pack on nearly every Chevrolet Volt, Opel Ampera, Holden Volt, and Cadillac ELR since production began. In fact, apart from vacation days and an occasional sick day, the mother-daughter duo has installed almost every battery pack since the Volt was in pre-production in 2009. The ELR launched earlier this year. All told – including Ampera – that's more than 80,000 electric vehicles. "We're a good team and our relationship is secondary when it comes to performing our jobs – but it's great to work alongside my daughter, said Osborne, a mother of five. Because the battery packs weigh more than 400 pounds each, automatic guided vehicles – robotic carts that use sensors to follow a path through the plant – deliver them just as the vehicle body structures glide into position overhead. The carts then lift the T-shaped packs, and Osborne and Watson guide them into the chassis and secure each one with 24 fasteners.

Camaro-based Trans Am SE Bandit Edition borrows Burt Reynolds

For some reason, modifying modern Chevrolet Camaros into the lurching, reincarnated shells of the Pontiac brand is still a thing. If you're the perverse sort that likes this kind of thing, you should check out the latest product from the Trans Am Depot, which comes complete with an endorsement from the star of Smokey and the Bandit, Burt Reynolds. Yes, the new Trans Am SE Bandit Edition has been signed and endorsed by the man himself, but what's important here is not the signature on the dash, it's the bits of Camaro that have been modified. Aesthetically, that means a Bandit-and-Frog-approved set of T-tops, a front-opening hood with a very large, prominent shaker scoop, an equally large and prominent screaming chicken, and Trans Am-inspired front and rear fascias. And naturally, Burt Reynolds' signature adorns the dash. There are plenty of reminders in the cabin about this car's Hollywood inspiration, too. Bandit decals can be found on the front headrests and center console lid, there are chicken wings on the Camaro-spec plastic door inserts, and the black-and-tan color scheme matches nicely with the exterior look. And power? Well, Sheriff Buford T. Justice would have a lot more trouble keeping up with this Trans Am than he did with the original. The 7.4-liter LSX V8 has been paired with a 2.9-liter supercharger which is good for 840 horsepower. It's fast and loud, and even if you can't get behind the look (we can't), at least this Camaro-in-Trans Am's clothing can impress with its performance. The Bandit Edition is limited to just 77 units with prices starting around $115,000. You can check out the official video from Trans Am Depot, which comes with a decent helping of Burt Reynolds, up top. Related Video: