Chevrolet Express 3500 Handicap Van - 12 Passenger Seating Without Wheelchair on 2040-cars

Auto blog

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

Next Chevy Volt will be 2016 model and ride on new chassis

What do we know about the 2016 Chevy Volt? Well, for now, all we can do is try to put the puzzle together without the box. Thankfully, a new batch of pieces has arrived from a new report in Edmunds, which says that the 2016 model year will introduce the second generation of a car that hasn't been dramatically updated since it went on sale in 2010. The new Volt is getting an "evolutionary styling change" and will ride on a new front-drive platform that has been developed by General Motors. GM's Kevin Kelly told AutoblogGreen that he has "no comment on future products," but he did acknowledge that Chevrolet is working on a second-generation Volt, "but I can't say anything about timing." Everybody already knew that a next-gen Volt is coming, so that's not a surprise. What we don't know is any real concrete information on the car itself. The few tidbits of information we do have help define the outlines of the next version of Chevy's halo car, but they're not confirmed yet. For the record, they range from the eye-raising (a $10,000 price drop) to the logical (20 percent more electric range). We can't see the whole picture yet, but the pieces do point to the 2016 Volt, which would be released next year sometime, being a much bigger deal than the last update, when the Volt's range was increased by three electric miles thanks to a battery capacity increase of 16 kWh to 16.5.

GM might outsource vans to AM General

General Motors will possibly boost production of the Chevrolet Colorado and GMC Canyon at the Wentzville Assembly Plant in Missouri by contracting out some commercial van manufacturing to AM General. Demand for the two midsize trucks continues to boom, and GM would like to take advantage of the strong market for them. The possible deal came to light in a letter to workers at the factory, according to Automotive News. "This potential partnership would free up production capacity and allow the organization to capitalize on our ability to build midsize trucks to further satisfy customer demand," a portion of the document allegedly said. AM General would reportedly only take over assembly of the cutaway versions of the Chevy Express and GMC Savana. Customers and critics have quickly embraced the latest Colorado and Canyon since their introduction. The Chevy just won back-to-back Motor Trend Truck of the Year awards. GM also had to add a third shift and extra workers in 2014 just to keep up with demand. The Wentzville plant even increased employment on the weekends earlier in 2015 to assemble an extra 2,000 of the trucks each month. While the two pickups boom, deliveries for the Chevy Express and GMC Savana are down 26.9 percent and 26.6 percent respectively through the first 10 months of the year. GM doesn't break out numbers for the cutaway versions, but they make up about a third of production, according to Automotive News. AM General built the Humvee for the US military and does some contract work with automakers. For example, the company's Indiana factory now produces the Mercedes-Benz R-Class for export to China. Here's hoping this potential deal will help both GM and AM General keep their factories humming. Related Video: