2013 Chevrolet Equinox Fwd 4dr Lt W/1lt on 2040-cars

Auto blog

Experimental mid-engine XP-819 Corvette going up for auction

It seems to be commonplace that when a new Corvette is in development, rumors swirl about a possible mid-engine layout. As is the case of Chevy's most recent C7 Corvette, these rumors never pan out.
In any case, the idea for a 'Vette with an engine mounted behind the driver can probably all be traced back to a single car, the 1964 XP-819 prototype. Built as an "engineering exercise" back in 1964, the prototype was designed with a rear-mounted engine. History tells us that the idea of a rear-engine Corvette fizzled, and the XP-819 was eventually cut up into pieces and stored at a shop in Daytona Beach, FL.
After sitting for untold years, a restoration project started on the car, and while it isn't yet fully completed, the current owner of the car, Mid America Motorworks, will have the car on display at the 2013 Amelia Island Concours d'Elegance as a "driveable chassis" with hopes of having a fully completed car ready to bring to next year's show.

GM recalls 83,572 SUVs for ignition switch issue

General Motors is recalling 83,572 SUVs from the 2011 and 2012 model years over a potential ignition lock actuator issue. In affected vehicles, the actuator isn't the right size, which could cause the ignition to get stuck in the "Start" position, and then either due to a jarring event or a "cool interior temperature" the ignition could switch back to the "Accessory" position. Doing so would cause a loss of power assistance and the airbags might not deploy. This is a different ignition issue than the one that's been ongoing for the past year. GM said it expects that less than 500 vehicles suffer from the problem, but that the pool could include vehicles from 2007 through to 2014 that have already been fixed, but with defective parts. The 2011-2012 SUVs included in the National Highway Traffic Safety Administration notice: Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado HD, Silverado LD, Suburban, Tahoe, GMC Sierra LD, Sierra HD, Yukon, and Yukon XL vehicles. GM will notify owners and dealers will inspect the ignition lock housing to see if it needs a free replacement. RECALL Subject : Ignition Lock Actuator may Bind Report Receipt Date: DEC 30, 2014 NHTSA Campaign Number: 14V827000 Component(s): ELECTRICAL SYSTEM Manufacturer: General Motors LLC SUMMARY: General Motors LLC (GM) is recalling certain model year 2011-2012 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado HD, Silverado LD, Suburban, Tahoe, GMC Sierra LD, Sierra HD, Yukon, and Yukon XL vehicles. In the affected vehicles, the ignition lock actuator may bind, making turning the key difficult or causing the ignition to get stuck in the "Start" position. CONSEQUENCE: If stuck in the "Start" position, the ignition may suddenly snap back into the "Accessory" position, causing a loss of engine, steering, and braking power, increasing the risk of a vehicle crash. If the vehicle is in a crash, the air bags may not deploy, increasing the risk of occupant injury. REMEDY: GM will notify owners, and dealers will inspect and replace the ignition lock housing, as necessary, free of charge. The manufacturer has not yet provided a notification schedule. Owners may contact GM customer service at 1-800-458-8006 (Cadillac), 1-800-222-1020 (Chevrolet), or 1-800-462-8782 (GMC). GM's number for this recall is 14696 for the original equipment, and 14912 for the service replacement parts.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck