2012 Chevy Corvette 2lt 6-spd Nav Hud Torch Red 22k Mi Texas Direct Auto on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

First 2015 Chevy Corvette Z06 engine blows up at just 891 miles

You've waited and watched and waited some more for the arrival of your 650-horsepower, $78,000 Chevrolet Corvette Z06. Finally, that joyous day arrives and you eagerly, but gingerly, begin to break-in the 6.2-liter supercharged V8 monster under your hood. Then 900-odd miles after delivery, your excitement grinds, quite literally, to a halt. That's what the owner of one 2015 Z06 claimed happened to him when a simple break-in drive resulted in a lunched engine. The owner, known as Lawdogg149 on Corvette Forum, says he was out breaking-in his car ahead of a January track event when it happened. "While making a pull from 35 miles per hour, I accelerated and shifted short of redline, and boom - the car began knocking. I pulled over and popped the hood. I could hear a loud knock coming from the No. 6 cylinder area along with a serious, grinding, metal-on-metal sound coming from the supercharger area," Lawdogg wrote. A subsequent trip to the dealer confirmed his concerns, with the service facility telling Lawdogg that the No. 6 valvetrain had failed. The dealer couldn't research the issue further, though, as General Motors requested the engine be returned for a more thorough evaluation. The good news for the Z06's unlucky owner, at least, is that GM will be covering the engine replacement under warranty, an expense that Corvette Forum estimates is a nearly $24,000 procedure. At this point, the two leading theories behind the engine's detonation involve a manufacturing defect – which could be why GM is so keen to tear the blown powerplant down – or a mistake on the part of Lawdogg. As Motor Authority points out, such an error could be something as simple as the Z06's owner accidentally shifting to first rather than third during his 35-mph pull. If, however, there's a deeper manufacturing problem with the Z06's engine, this might not be the only case we end up hearing about.

GM posts $4 billion third-quarter profit thanks to trucks and SUVs

DETROIT — General Motors is posting huge third quarter numbers, pulling in $4 billion in profit over three months after losing money due to the virus outbreak. GM's adjusted earnings were $2.83 per share, easily outpacing Wall Street's per-share projections of $1.43, according to a survey by FactSet. Revenue of $35.5 billion also edged out most expectations. Shares jumped almost 6% before the opening bell Thursday. The company swung back from a $806 million loss in the second quarter, when it was restarting factories shuttered for safety during the early stages of the pandemic. The Detroit automaker joined most global automakers in reporting better-than-expected earnings from July through September as sales across the globe started to rebound from coronavirus lockdowns, especially in China. GM sales in China jumped 12% in the third quarter, with sales of its Buick and Cadillac brands both rising more than 25%. In the U.S., GMÂ’s most profitable market, sales fell 9.9% in the third quarter compared with a year ago, but were a dramatic improvement over the 34% drop in the second quarter. Sales improved sequentially each month, the automaker said, an encouraging trend. GMÂ’s profit was boosted by higher-priced pickup trucks and large SUVs, which have seen strong sales in the U.S. through the pandemic. It was the best quarter on record for GM's Chevrolet Blazer. Sales of the Cadillac XT6 spiked 45% in the U.S. over last year. Large pickups also sold well. GM also said it was pumping $2 billion into its Spring Hill, Tennessee manufacturing plant to push its transition to produce electric vehicles. Last week, crosstown rivals Fiat Chrysler and Ford reported strong third-quarter net income. FCA said it made $1.4 billion for the period, while Ford earned $2.39 billion. Related Video: Earnings/Financials Buick Cadillac Chevrolet GM GMC