2010 Chevrolet Corvette Grand Sport Convertible 2- on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

1983 Motorweek showdown pits Porsche 928S vs. Chevy Camaro Z28

Last month, Motor Trend threw the Camaro Z/28 and Porsche 911 GT3 into the bear pit and let them fight it out. Way back in 1983, MotorWeek had the same idea, comparing the Camaro Z/28 to the Porsche 928S. At the time, the Camaro was America's best selling sports coupe, the 928S was Porsche's top-of-the-line model that also had the highest top speed of any car sold here. And the price differential was even more stark then: $13,600 for the Camaro, $45,000 for the Porsche. That put the Z/28's cast-iron, 5.0-liter V8 with 190 horsepower and 240 pound-feet of torque against the all-aluminum 4.7-liter V8 with 234 hp and 263 lb-ft in the 928S. Even with that and the Camaro being 14 inches longer than the Porsche, the American was a surprising 40 pounds lighter than the German. The show took them to Summit Point Raceway in West Virginia to see how close a relative performance bargain could hang with a the German GT. Both had five-speed manual transmissions, but the high-speed corners and tight sections of Summit Point would test other handling variables, including the "bone-rattling" Camaro's solid rear axle and disc and drum brake setup vis-a-vis the four-wheel disc brakes and independent suspension on the "firm-but-smooth" Porsche. Paradoxically, the larger disparity 22 years ago resulted in a closer result. Check out the video to see how the Summit was won. News Source: MotorWeek via YouTube Chevrolet Porsche Coupe Luxury Performance Classics Videos chevy camaro z28 porsche 928 retro review

Meet the mother-daughter team that's worked on almost every Chevy Volt

It's Mother's Day, and we're soft enough we love our mothers enough to share a new video from General Motors with you. In it, we meet Monique Watson (left) and Evetta Osbourne, a mother-daughter team that works at the Detroit-Hamtramck Assembly where GM makes the Chevy Volt (along with all of GM's other plug-in hybrids: the Opel Ampera, Holden Volt and Cadillac ELR). The two work side-by-side and have installed the lithium-ion battery pack on almost all of those vehicles - nearly 80,000 of them - since GM started making the pre-production Volts in 2009. In a prepared statement, Watson said that she likes working next to her mom, day in and day out, and they the two are totally in sync when it comes to putting the 400-pound, 16.5-kWh packs into the vehicle undersides. They two can also share stories throughout the day, and Watson said, "The arrangement has absolutely improved our relationship." Osborne started working at Detroit-Hamtramck in 1999, Watson since 2006. If you're driving a Volt today, you probably have them to thank for doing a bit of the work putting your car together. See a short video of them in action below. It's Always Mother's Day for Detroit-Hamtramck Duo Mother, daughter install lithium-ion battery pack in nearly all GM electric vehicles 2014-05-08 DETROIT – For Detroit resident Evetta Osborne, every day is Mother's Day. That's because she literally works side by side with her daughter, Monique Watson, at General Motors' Detroit-Hamtramck assembly plant. They have installed the lithium-ion battery pack on nearly every Chevrolet Volt, Opel Ampera, Holden Volt, and Cadillac ELR since production began. In fact, apart from vacation days and an occasional sick day, the mother-daughter duo has installed almost every battery pack since the Volt was in pre-production in 2009. The ELR launched earlier this year. All told – including Ampera – that's more than 80,000 electric vehicles. "We're a good team and our relationship is secondary when it comes to performing our jobs – but it's great to work alongside my daughter, said Osborne, a mother of five. Because the battery packs weigh more than 400 pounds each, automatic guided vehicles – robotic carts that use sensors to follow a path through the plant – deliver them just as the vehicle body structures glide into position overhead. The carts then lift the T-shaped packs, and Osborne and Watson guide them into the chassis and secure each one with 24 fasteners.