1966 Corvair Corsa Convertable Sedona Az Ac Tele Am/fm Remote Mirror Power Top on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Experimental mid-engine XP-819 Corvette going up for auction

It seems to be commonplace that when a new Corvette is in development, rumors swirl about a possible mid-engine layout. As is the case of Chevy's most recent C7 Corvette, these rumors never pan out.
In any case, the idea for a 'Vette with an engine mounted behind the driver can probably all be traced back to a single car, the 1964 XP-819 prototype. Built as an "engineering exercise" back in 1964, the prototype was designed with a rear-mounted engine. History tells us that the idea of a rear-engine Corvette fizzled, and the XP-819 was eventually cut up into pieces and stored at a shop in Daytona Beach, FL.
After sitting for untold years, a restoration project started on the car, and while it isn't yet fully completed, the current owner of the car, Mid America Motorworks, will have the car on display at the 2013 Amelia Island Concours d'Elegance as a "driveable chassis" with hopes of having a fully completed car ready to bring to next year's show.

2014 Chevy Cruze Diesel destined for Chicago debut

It's been a little over a year and a half since General Motors first confirmed plans to offer a diesel-powered Chevrolet Cruze here in the United States, and we've now learned that the oil-burning compact will debut under the lights of the Chicago Auto Show in February. According to GM Authority, the Cruze Eco-D will be introduced as part of the entire 2014 model year Cruze range, set to go on sale in the second quarter of this year.
Earlier reports have indicated that the diesel Cruze will be able to achieve fuel economy numbers in the range of 50 miles per gallon. For comparison, the similarly sized Volkswagen Jetta TDI is rated at 30/42 mpg city/highway, but as we found out in our long-term test of the 2011 model, hitting 50 mpg was a piece of cake.
Official specifications will be released at the time of the 2014 Cruze's unveiling, though reports have stated that the sedan will be powered by a reworked version of the 2.0-liter turbo-diesel inline-four found in the Holden Cruze CDX overseas. In that application, the four-pot oil-burner produces 160 horsepower and 265 pound-feet of torque - increases of 20 hp and 29 lb-ft over the 2.0-liter engine used in VW's Jetta TDI.