Clean Carfax From Ga Rust Free 2.9l 4 Cyl 5 Speed Manual Cd Cold A/c Low Miles on 2040-cars

Auto blog

Junkyard Gem: 1986 Chevrolet Sprint Plus

General Motors sold second- and third-generation Suzuki Cultuses with Geo or Chevrolet Metro badging in the United States from 1989 through 2001 model years, and we've all seen plenty of those cars on the street over the years. The first-generation Cultus was sold here as well, with Chevrolet Sprint badges, and I've found a rare example of the Sprint five-door hatchback in a Northern California car graveyard. The Chevy Sprint first appeared on the West Coast as a 1985 model, then became available everywhere in the United States for the 1986 through 1988 model years (in Canada, it was sold as the Pontiac Firefly). It was available here as a hatchback with three or five doors; for 1986 only, the five-door was badged as the Sprint Plus. Soon enough, The General would be selling many more Asian-built cars with Detroit badges here. Isuzu I-Marks were sold as Chevrolet/Geo Spectrums starting in the 1986 model year, while Daewoo provided the Pontiac LeMans two years later. Under the hood, a 1.0-liter three-cylinder rated at 48 horsepower. The five-door Sprint cost $5,580 in 1986, which was $200 more than the three-door (those prices would be $15,445 and $14,891 in 2023 dollars). I've documented seven discarded Sprints prior to this one (including an extremely rare Turbo Sprint), and all of them were three-doors; we can assume that price was the most important factor for Sprint buyers. Gasoline prices were crashing hard during the middle 1980s, but memories of gas lines and odd-even-day fuel rationing from 1979 remained strong. What cars competed with the '86 Sprint on sticker price? Well, there was no way to undercut the hilariously affordable (and terrible) Yugo GV, which cost $3,990. The much bigger (but still pretty bad) Hyundai Excel listed at $4,995, while Toyota would sell you a sturdy (but zero-fun) Tercel starting at $5,448. Even the wretched Chevy Chevette — yes, it was still available in 1986 — cost $5,645. The original buyer of this car was willing to shell out an extra $395 to get an automatic instead of the base five-speed manual. That's about $1,093 in today's money. This car must have been slow. By the end, the doors were held shut with duct tape, but it still stayed alive until age 37. 53 miles per gallon on the highway! It does everything. The camels of the highway.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GMC Canyon, Chevy Colorado diesels finally heading to dealers

Customers who have been waiting to receive their diesel-powered Chevrolet Colorados and GMC Canyons should be relived to hear that GM will finally start to ship them out of the Wentzville Assembly Plant. "The highly anticipated 2016 GMC Canyon diesel has begun shipping to dealers," a company spokesperson confirmed to The Detroit News. The trucks originally had a fall launch date, but a final review forced a delay in deliveries. The 2.8-liter four-cylinder diesel in the midsize trucks produces 181 horsepower and 369 pound-feet of torque, and the company touts the engine's low emissions. The Environmental Protection Agency and California Air Resources Board even put the mill through extra scrutiny with a real world test in the wake of VW's diesel scandal, and the Duramax passed with no problems. At that time, a Chevy spokesperson told Autoblog that the models' launch was on track. The Duramax engine adds $3,730 to the price of a comparable V6 model, but they're the most fuel-efficient pickups on the market. The EPA estimates the twins at 31 miles per gallon highway, 22 mpg city, and 25 mpg combined in two-wheel drive form and 29/20/23 with four-wheel drive. Buyers likely can't wait to finally experience these pickups after reading a heap of positive reviews. The Colorado diesel recently earned Motor Trend's Truck of the Year award. We also came away impressed with it during our First Drive and liked the Canyon during our Quick Spin. Related Video: