Find or Sell Used Cars, Trucks, and SUVs in USA

1970 Real Ls6 Chevelle Ss 454 450hp Project Black 4 Speed Lots Nos Documented on 2040-cars

Year:1970 Mileage:41802
Location:

Boston, New York, United States

Boston, New York, United States
Advertising:

Auto Services in New York

Willowdale Body & Fender Repair ★★★★★

Automobile Body Repairing & Painting
Address: 92 S Bayles Ave, Greenvale
Phone: (929) 224-0634

Vision Automotive Group ★★★★★

Auto Repair & Service, New Car Dealers, Used Car Dealers
Address: 1177 Fairport Rd, Rush
Phone: (585) 249-9000

Vern`s Auto Body & Sales Inc ★★★★★

Auto Repair & Service, Automobile Body Repairing & Painting, Automobile Parts & Supplies
Address: 107 W Main St, Fort-Johnson
Phone: (518) 843-3424

Valvoline Instant Oil Change ★★★★★

Auto Repair & Service, Auto Oil & Lube, Automotive Tune Up Service
Address: 56 W Old Country Rd, Jericho
Phone: (516) 931-7887

Valanca Auto Concepts ★★★★★

Automobile Body Repairing & Painting
Address: 1171 Zerega Ave, Larchmont
Phone: (718) 828-2111

V & F Auto Body Of Keyport ★★★★★

Auto Repair & Service, Automobile Body Repairing & Painting
Address: 6 Cass St, Staten-Island
Phone: (732) 739-6202

Auto blog

GM recalls 8,500 Chevrolet Malibu models for rear suspension glitch

Mon, 04 Feb 2013

According to a letter from General Motors to the National Highway Traffic Safety Administration, flaws in the build process of the 2013 Chevrolet Malibu have led to the recall of 8,519 cars. Units built between December 6, 2011 and January 15, 2013 may have been assembled with rear suspension cradles that had insufficient torque applied to certain bolts. That out-of-spec assembly could lead to issues ranging from slight noises to a loss of vehicle control.
The problem was first noticed in December of last year by a GM test fleet driver and eventually tracked back to the improperly torqued bolts on the suspension cradle assembled through July 2012 by a supplier located not too far from the Malibu's Detroit/Hamtramck Assembly Plant. Since an official NHTSA recall notice has not been issued yet, it isn't clear whether or not Detroit-built Malibus were the only ones affected (the 2013 Malibu is also built at GM's Fairfax Assembly Plant in Kansas City, Kansas). Dealers will fix the problem by inspecting vehicles for proper torque specs, retightening if not within specs and, in some cases, perform a rear-wheel alignment.

2021 Chevy Colorado and GMC Canyon facelift spied

Fri, Sep 20 2019

The Chevy Colorado and its GMC Canyon twin have been on sale for a good long time now, and while things move a little more slowly on the truck side when it comes to facelifts and model changeovers, it seems like it’s about time. So itÂ’s no surprise to see some lightly camouflaged trucks running around ahead of what appears to be a minor refresh for the 2021 model year. Starting with the Colorado, it appears to have a bowtie hiding behind some camo in the center of the grille, which otherwise looks like the no-bowtie option you can get on 2019-and-up trucks. It could be that Chevy is keeping the no-bowtie grille design but allowing a bowtie to grace it, or it could be misdirection. Either way, the grille pattern adds a bit of flair to the otherwise staid front end design. There also appears to be a bit more shape to the lower air inlet, with echoes of some of the lower fascias of its bigger Silverado stablemate. The Canyon, on the other hand, shows more extensive front-end changes. At first glance, it looks to emulate some variants of the GMC Sierra, which would make sense given those modelsÂ’ changes for the 2020 model year. In particular, this Canyon has hints of Sierra HD, being more square and monolithic than the regular Sierra 1500s, although itÂ’s a little hard to tell with the camo covering the edges of the grille. It could certainly also adopt more rounded corners like the 1500s. Either way, itÂ’s more vertical and thereÂ’s less differentiation between the upper grille and lower opening. ThereÂ’s nothing in the way of changes around the sides or back, and while there may be some minor changes inside, we arenÂ’t expecting any. The word around town is that this isnÂ’t a full facelift, but rather a minor front end tweak thatÂ’ll just be a regular part of the model-year changeover. 

1956 Corvette SR-2 factory racer profiled

Mon, Jan 19 2015

The Chevrolet Corvette has earned its place as America's sports car, capable of taking on the best the world can throw at it. Much of that winning reputation was earned with victories on the track. Now, there was a chance to own an early piece of the nameplate's motorsport history in the form of a 1956 Corvette SR-2 racer, but some deep pockets were necessary to get it, with an estimate of $6.885 million. The story behind the SR-2 is fascinating. In 1956, famous General Motors designer Harley Earl's son was racing in a Ferrari. Obviously, that wasn't going to work given his father's position within the automaker, and Harley and Corvette engineer Zora Arkus-Duntov got to work on a faster racecar. Three were made. This one was reportedly the first, and for 1957 it also received a fuel-injected V8 making a claimed 331 horsepower and four-speed manual gearbox, according to "Corvette Mike," the owner and seller. The SR-2 went on display in Scottsdale, AZ appropriately timed to coincide with the big Barrett-Jackson auction there that wrapped up this weekend. The car wasn't part of that event; instead marque specialist Mike Vietro sold the racer as a private treaty sale. Company spokesperson Troy Worrell told Autoblog both the bids and identities of the bidders will remain undisclosed. The video above goes into even deeper detail about this rare, finned Vette or check out the car's full description for even more info.