1969 Chevrolet Chevelle on 2040-cars

Auto blog

Fullsize GM SUVs have a problem that's making owners sick

Some fullsize SUV owners are getting sick, thanks to a buffeting and vibration problem in 2015 model year examples of the Chevy Tahoe and Suburban, Cadillac Escalade, and GMC Yukon. According to owners' complaints to the National Highway Traffic Safety Administration, the issue can vary from an annoying vibration inside the cabin to an experience so severe that it leads to dizziness and headaches. General Motors is aware of the complaints, but the fix isn't so simple. According to spokesperson Tom Wilkinson to Autoblog, the company "has been tracking this issue for a while." The problem has a fairly low incidence rate, but when it does occur the issue can be "uncomfortable and annoying for owners." There's no precise cause for the issue, Wilkinson claims, and in some cases, simply balancing the tires or changing the door seals can make it go away. However, not all of the fixes are so simple. AutoGuide dug deep into the problem and discovered a GM preliminary information bulletin that advised dealers to remove the headliner and to check the roof's bonds to the bows that go across the vehicle. However, that document included a note that the solution might not entirely eliminate things. According to AutoGuide, adding Dynamat insulation to the roof sometimes helped the problem. A GM spokesperson also told AutoGuide the company fixed the problem at the end of the 2015 model year, and didn't go into any more detail. This roof issue seems linked to some of the worst droning in these SUVs. According to one complaint from a 2015 Suburban owner to NHTSA: "Roof will not remain attached to the roof bows. This causes the buffeting similar to a window being down when all are up. The results span from annoying to painful." A 2015 Yukon owner claims to have another alleged cause for the problem in a NHTSA complaint from February 2015. This person brought their SUV to the dealer seven times over the course of four weeks for vibrations. The dealer replaced the driveshaft, suspension components, and more, but nothing worked. According to an engineer to the service adviser: "In an effort to prevent roll overs, they designed the frame and body mounts too stiff. There are 40 engineers working on issues, they have no solutions that work across the board." Wilkinson told Autoblog that GM is working with customers on an individual basis to rectify things. Since these are newer vehicles, dealers should also fix the problem under warranty.

GM Design shows what could have been and what might be

We periodically like to check in with GM Design's Instagram account to see what they're cooking up. Even better is when we catch a glimpse of an alternate history of what legendary designers from The General's past were thinking, though those ideas may not have made it into production. This week, for example, the account posted some illustrations from George Camp, whose career at GM spanned nearly four decades, from 1963 to 2001. One of the renderings is of what appears to be a 1971-72 Pontiac GTO Judge, but with two headlights instead of the production unit's quad beams. The rear departs from the canonical version most dramatically, with a massive integrated wing. Other bits that didn't make the production cut include large side vents, a gill-like side marker and rectangular intakes below the headlights that wouldn't be out of place on a modern design today. Amazingly, from what we can make out of the date, it appears that the drawing was done sometime in 1965, which makes it quite prescient.           View this post on Instagram                       A post shared by GM Design (@generalmotorsdesign) There's also a very aerodynamic interpretation of a Corvette ZR-1. To our eyes it splits the difference between the 1986 Corvette Indy concept and a fourth-generation F-body Pontiac Firebird, so perhaps parts of Camp's work on this sketch did make it into physical form. There's also a radical sports car concept from May 1970 that resembles the Mazda RX-500 concept from the same year, a Syd Mead-looking Cadillac coupe, and an Oldsmobile with a cool take on the company's trademark waterfall grille and elements of the Colonnade Cutlass at the rear. Other recent posts include a FJ Cruiser-like off-road EV, a sleek coupe with the Chevy corporate grille, and a rendering of a Silverado-esque pickup that looks far better than the current production version.           View this post on Instagram                       A post shared by GM Design (@generalmotorsdesign) It's pretty easy to lose hours in the account, but it's always fascinating to see GM's visions of what could have been and what might be. Related Video:

Next-gen Chevy Volt will get 1.5-liter, four-cylinder engine

As General Motors gets ready to unveil the new Chevy Volt at the Detroit Auto Show in January, it's starting to reveal a few more details about the updated plug-in hybrid. Today should be fruitful on that front, thanks to an event GM is hosting today that focuses on the new Volt, and we've just had the first bit of new: a bigger engine is coming. Since the beginning, the Volt has used a 1.4-liter, four-cylinder engine as a range extender when the battery runs dry. The second-generation model will instead get a slightly larger 1.5-liter, four-cylinder engine that will be built in Flint, MI. That's a step up from the various engines that have been a part of the 2016 Volt's rumored mills, everything from a 1.0-liter or 1.2-liter three-cylinder to a 2.0-liter turbo. The confirmation about the new 1.5-liter powerplant was found in Automotive News, where we also heard again that GM is going to start building the new Volt's electric drive unit in Detroit, moving production up from Mexico. We will have more information on the 2016 Chevy Volt later today.