1962 C10 Short Bed Vortec 5.7 V8 Fleetside Ac Swb Fleet Patina Hotrod Clean on 2040-cars

Auto blog

GM recalls 200k Hummer H3s for fire risk

An issue with fires erupting in some Hummers has prompted General Motors and the National Highway Traffic Safety Administration to issue a recall for nearly 200,000 vehicles around the world. The bulk of them are in the United States. According to the first statement (below) obtained by Autoblog from GM, the issue stems from the HVAC system in Hummer H3 models. The connector module for the blower motor has, in certain cases, overheated, melted the surrounding plastic, and started a fire. 42 such cases have been reported, including three instances of occupants citing minor burns. GM confirms that two of those three cases lead to the vehicle being destroyed in the fire, but states that no crashes or fatalities have resulted. The issue affects 196,379 examples of the 2006-10 H3 wagon and the 2009-10 H3T pickup, with 164,993 estimated to be in the United States. In order to fix the issue, dealers are being instructed to replace the relevant parts of the connector and harness. In a second, unrelated campaign, GM is also calling in 50,731 Chevy Spark and Sonic small cars – 45,785 of them in the US – due to a software glitch. In those affected vehicles fitted with the base radio and OnStar system, the audio system may not be able to switch out of turn-by-turn direction mode, causing the display to go blank and all sound to mute – including key safety warnings. In addition, the system may not switch off, draining the battery. GM states that no crashes, injuries, or fatalities have resulted from this issue, and all that dealers will need to do in this case is reflash the software. Related Video: General Motors is recalling 164,993 2006-2010 model year HUMMER H3 and 2009-2010 model year HUMMER H3T models in the U.S. In certain vehicles, the connector module that controls the blower motor speed in the heat/vent/air conditioning (HVAC) system may overheat under extended periods of operation at high- and medium-high speeds. The heat could melt the plastic surrounding the connector module, increasing the risk of a fire. Dealers will replace the affected portion of the connector and harness. GM is aware of three reported minor burns and 42 fires but no crashes or fatalities related to this condition. Including Canada, Mexico and exports, the total recall population is 196,379. ### General Motors is recalling 45,785 2014-2015 model year Chevrolet Sparks, and 2015 model year Chevrolet Sonics in the U.S.

LG Chem's troubled Chevy Volt battery plant hiring once again

The Michigan battery plant known for paying its workers to do nothing has turned things around and is now hiring more workers, specifically to do something. South Korea-based LG Chem, which runs the factory to supply the Chevrolet Volt extended-range plug-in vehicle with its lithium-ion batteries, held a job fair recently to bring on 40 new employees in order to meet higher battery demand, according to WZZM, the ABC affiliate for Grand Rapids, MI. The LG Chem factory is in Holland, MI, about 30 miles west of Grand Rapids, and it made its first batteries last year. Prior to that, though, the factory gained notoriety after a US Department of Energy (DOE) probe found that workers there were getting paid to do, well, nothing. That's because demand for the battery packs was so low that it cost less for the plant to sit idle. The DOE was conducting the probe because of its financial grant to LG Chem. But that was then and today is today. LG Chem is looking to ramp up production in advance of the second-generation Volt. That 2016 model-year version is said to have a longer all-electric range and better performance and will ride on a new chassis, but few official details have surfaced. We will know more when we get our first look at the car at the Detroit Auto Show in January.

Chevy's 6.6-liter Duramax is pretty much all new

To say there's a heated battle in heavy-duty pickups is an understatement, with Chevrolet, Ford, and Ram constantly trading blows of increased torque, horsepower, and towing capacity. The latest salvo is the revised, more powerful turbo diesel 6.6-liter Duramax V8 in the 2017 Chevy Silverado. It has 910 pound-feet of torque, an increase of 145, putting it nearly level with the Ford Super Duty. Here's a closer look at where those gains come from. How exactly did Chevrolet add all that torque plus 48 horsepower? The automaker essentially took a fine-tooth comb to the entire engine. Chevy says it changed 90 percent of the V8, and the cumulative effect of those small changes adds up to big increases. As you might guess, the turbocharger is updated. The larger unit features electric actuation of the variable nozzle turbine (VNT), and what Chevy calls a double axle cartridge mechanism that separates the VNT moving parts from the housing. That helps with heat performance as well, with a claim that the exhaust side of the turbo can run continuously up to 1,436 degrees Fahrenheit. Helping that cause are six exhaust gaskets made of Inconel - an nickel alloy that contains chromium and iron – and upgraded stainless steel for the exhaust manifold. Despite having the same cast iron cylinder block, albeit with some minor enhancements, the engine has new cylinder heads, pistons, piston pins, connecting rods, and crankshaft, which have all been upgraded to handle 20 percent higher cylinder pressures. Alongside the increase in pressure, Chevrolet also increased the cylinder head's structure with a honeycomb design. The pattern features high-strength aluminum with dual layer water jackets that not only improve strength, but also optimize water flow for better cooling. For 2017, the cylinder head also benefits from integrated plenum that aids the engine in getting more air under heavy loads. The cylinder head isn't the only component to get a minor update, as the pistons have a larger diameter pin for improved oil flow. The same detailed improvements has been bestowed to the humble connecting rods (second in our hearts only to the inanimate carbon rod). The new design has the bolts oriented roughly 45-degrees to the rod instead of parallel. The angle split design, as it's called allows for easier passage through the cylinder.