1957 Chevrolet Bel Air/150/210 Bel-air on 2040-cars

Auto blog

Fewer than 1 in 3 Chevy dealers earn right to initially sell C7 Corvette

Looking to make the launch of the 2014 Corvette Stingray as efficient as possible, Chevrolet will be limiting the numbers of its dealers that can sell the all-new coupe and convertible. According to Automotive News, sales of the C7 Corvette will initially be limited to less than a third of Chevy's total dealership network when the 'Vette goes on sale this summer.
Only 900 dealers out of more than 3,000 locations nationwide will be allowed to sell the new Corvette at first, and the reason for this is so that there are no shortages at dealers that can actually get the cars sold. The article says that the 900 dealerships chosen represented 80 percent of total Corvette sales in 2012.
Some of the requirements dealers had to make to get initial allocation of Stingray sales include having sold at least four Corvettes in 2012 and having a Corvette Stingray specialist who will be required to have gone through a training session costing more than $2,000 per attendee. Once demand for the 2014 Corvette Stingray begins to subside - approximately six to nine months after it goes on sale - then allocation could open up to more dealers, but the report indicates this could happen following the 2014 model year.

GM recalling 686k Lambda-platform models for hatch repair

General Motors is recalling 686,287 units of its Lambda platform crossovers. On models equipped with a power rear hatch the system can potentially fail. This campaign includes the 2008-2012 Buick Enclave, 2009-2012 Chevrolet Traverse, 2007-2012 GMC Acadia, and 2007-2010 Saturn Outlook. According to GM's documents to the National Highway Traffic Safety Administration (as a PDF), dirt can get into a portion of the strut that holds up the hatch and cause the part to prematurely fail. There's a redundancy in place called the Prop Rod Recovery system that's designed to shut the liftgate if there's a malfunction. However, if the breakdown happens too quickly after the hatch is opened the prop rod might not work the way it's supposed to. If someone were in the way of the falling liftgate, they could be hurt. For the repair, dealers will update the software for the power liftgate actuator motor control unit to prevent the hatch from closing so quickly. They'll also check the operation of the system afterward. Related Video: RECALL Subject : Liftgate Struts may Fail and Liftgate may Fall Report Receipt Date: JUN 30, 2015 NHTSA Campaign Number: 15V415000 Component(s): STRUCTURE Potential Number of Units Affected: 686,287 All Products Associated with this Recall Vehicle Make Model Model Year(s) BUICK ENCLAVE 2008-2012 CHEVROLET TRAVERSE 2009-2012 GMC ACADIA 2007-2012 SATURN OUTLOOK 2007-2010 Details Manufacturer: General Motors LLC SUMMARY: General Motors LLC (GM) is recalling certain model year 2008-2012 Buick Enclave vehicles manufactured January 3, 2007, to February 29, 2012, 2009-2012 Chevrolet Traverse vehicles manufactured July 6, 2008, to February 29, 2012, 2007-2012 GMC Acadia vehicles manufactured September 15, 2006, to February 29, 2012, and 2007-2010 Saturn Outlook vehicles manufactured August 17, 2006, to March 18, 2010. The affected vehicles, equipped with the power liftgate option, have gas struts that hold the power liftgate up when open. These struts may prematurely wear and the open liftgate may suddenly fall. CONSEQUENCE: If the open liftgate unexpectedly falls, it may strike a person, increasing their risk of injury. REMEDY: GM will notify owners, and dealers will update the software for the power liftgate actuator motor control unit so that the motor will prevent the rapid closing of the lift gate, free of charge. The manufacturer has not yet provided a notification schedule.

GM patent reveals new two-stage turbocharger

Modern turbochargers may be some of the best ever made, but performance is something that engineers are always trying to improve. According to GM Inside News, General Motors (GM) is hoping to alleviate some of the negative aspects of a two-stage turbocharger setup with a newly-patented design. The patent, that was filed on May 19, 2016, reveals a clever bypass system that allows the engine, a four-cylinder unit, to optimize both the low-pressure and high-pressure inlets for its respective functions. According to the filing, a conventional two-stage turbocharger setup is engineered to allow both turbines to operate simultaneously at low and mid engine speeds. At high engine speeds, only the low-pressure turbine works. The setup can't isolate either the low or high pressure side, which can impair low-end performance. GM's new two-stage turbocharger setup looks to eliminate this by linking the high-pressure turbo to the exhaust manifold through the high-pressure inlet duct. The low-pressure turbo is attached to the high-pressure turbo by a low-pressure inlet duct, which is linked to a connecting channel. A single actuator that is housed in the exhaust manifold creates a bypass that can opens the high-pressure inlet or close the connecting channel. Depending on what the engine load and speed is, the ECU guides the actuator—a single rotating spindle with discs corresponding to flanges on the high and low pressure sides—to isolate one of the two turbos. Isolating the turbos allow the respective inlets to be engineered for the best possible fluid dynamic performance. The setup should increase performance and decrease lag. There's no word on what car this setup will make an appearance on, but it will most likely be used in premium vehicles before trickling down to the rest of GM's vehicles. Related Video: News Source: GM Inside News, AutoGuide via GM Authority Cadillac Chevrolet GM Technology Sedan turbo patent engine turbocharging