4dr Sedan Lt W/2lt Low Miles Automatic Gasoline Ecotec 1.6l Dohc 16-valve 4-cyl on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Bob Lutz builds the case for a mid-engined Corvette

Rumors of a mid-engine Corvette are like automotive industry folklore at this point. Every once in a while, news pops up that it might be happening or is under development, but nothing actually ever comes to fruition as something people can actually buy. The latest spy shots strongly suggest a mid-engine 'Vette is in the cards, yet again, possibly for 2018. Now, an op ed by former General Motors executive (and definite performance car fan) Bob Lutz in Road & Track gives the inside scoop on the history of one of these proposals and lays out how to make it happen today. According to Lutz, the company's engineers believed the C6 ZR1 was at the limit for front-engine, rear-wheel drive performance in that package, and the only solution was to move the powerplant behind the driver. Lutz even got then CEO Rick Wagoner on board. The scheme made it at least as far as clay models for mid-engine versions of the 'Vette and Cadillac XLR. Eventually, a lack of money got in the way, though, bringing the project to an end. Lutz puts a lot of faith in GM's current leaders, especially Mary Barra and Mark Reuss. He thinks the chances of a mid-engine 'Vette happening this time are better than 50 percent. The model, rumored to be named Zora, could offer over 700 horsepower in an ultra lightweight body and be priced at about $120,000 to "suck the doors off everybody." Head over to Road & Track to get some insights from this highly respected and entertaining auto industry veteran. Related Video:

GM veteran Bryan Nesbitt tapped to head Buick design

General Motors styling veteran Bryan Nesbitt (pictured above) took over a new role on Monday as executive director of global Buick design and global architectures. Andrew Smith, who previously did that job and also coordinated the look for Cadillac, has remained in charge of the pen at Caddy with this shift. Nesbitt rose to prominence when he designed the Chrysler PT Cruiser, according to Automotive News. He joined GM in 2001 and has been there ever since in multiple high-level roles. In 2007, he was appointed vice president of design for North America and was later briefly general manager of Cadillac in 2009-2010. Nesbitt took over as the vice president of GM's international operations design in China in 2011. This shuffle also moves Ken Parkinson, currently styling boss for Chevrolet trucks, to China as design vice president there. In addition, John Cafaro becomes the person in charge of the look for Chevy globally, rather than previously splitting that role between cars and trucks with Parkinson. GM Global Design Leadership Changes – effective June 1, 2015. Bryan Nesbitt, Design Vice President, GM China will repatriate to North America and assume the position of Executive Director, Global Buick and Global Architectures. He will be located in Warren, MI. Bryan will be the design Champion for Buick in the US and China. Ken Parkinson, Executive Director, Global Chevrolet Trucks and Global Architecture will assume the position of Design Vice President, GM China. He will be based in Shanghai, China. Andrew Smith, Executive Director, Global Cadillac and Buick Design will assume the position of Executive Director, Global Cadillac. He will continue to be the design Champion for the Cadillac brand. In addition, he will continue to lead the Global Color & Trim team. He will be based in Warren, Michigan. John Cafaro, Executive Director, Global Chevrolet Cars will assume the position of Executive Director, Global Chevrolet. He will be the design Champion for Chevrolet. In addition, John will lead the exterior components and accessories team. He will continue to be based in Warren, MI. The roles and responsibilities of Helen Emsley, Mark Adams, Carlos Barba, Clay Dean, Michael Simcoe, and Teckla Rhoades remain the same. Related Video: The video meant to be presented here is no longer available. Sorry for the inconvenience.