1949 Dodge Coronet Coupe

TRADES AND OFFERS ARE CONSIDERED!

Top Line Information


Year:	1949	VIN:	31394971
Make:	Dodge	Stock:	2153
Model/Trim:	Coronet Coupe	Condition:	Pre-Owned
Body:	Coupe	Exterior:	Black
Interior:	Tan	Mileage:	56,000

Video

Additional Photos

* * * Click Photos to Enlarge * * *

Contact Ken Snow
Phone: 507-386-1726

Description

This car has been in the same family since NEW! It has only 56,000 original miles! here are more specs on the car----

Model Designation: Wayfarer Six: D29; Coronet Six: D30; Meadowbrook Six: D30

Wheel base: Wayfarer: 115; Coronet Six, Meadowbrook Six: 123-1/2

Valve Location: In block

Bore and Stroke: 3-1/4 x 4-5/8

Piston displacement, Cubic Inches: 230.2

Compression ratio: 7.0

Maximum Brake Horsepower: 103 @ 3600 RPM

Maximum Torque Lbs.Ft. @ RPM: 190 @ 1200 RPM

Normal Oil Pressure Pounds: 40

TUNE UP SPECIFICATIONS (all models)

Spark Plug Make: Auto-Lite AR5

Spark Plug Gap, Inch: .025

Firing Order: 153624

Timing Mark: Top Dead Center; location: Vib. Damper

Engine Idle Speed, RPM: w/manual transmission: 475

Cylinder Head Torque Lbs.Ft.: 70

Compression Pressure & Cranking Speed: 120 min.

Voltage & Polarity: 6 volts, positive ground

PISTON AND RING SPECIFICATIONS

Fitting Pistons with Scale: Pistons removed from above. Shim thickness: .002

Pounds on a Pull Scale: 5 to 7

Ring End Gap: In tapered bores, fit rings in tightest portion of ring travel
Compression: .007
Oil: .007

Clearance in Groove: Compression: Top ring: .0025-.004; second ring: .002-.0035; Oil: .001-.0025

Wristpin Diameter, Inch: .8591-.8593

VALVE SPECIFICATIONS

Operating Clearance:
Intake: .008 Hot; Exhaust: .010 Hot

Valve Seat Angle, degrees: 45

Clearance for Timing Intake: .014

Valve Timing: (BTDC = before top dead center; ATDC = after top dead center)
Intake opens: 8 BTDC
Exhaust Closes: 7 ATDC

Valve Spring Pressure Pounds at Inches Length:
Inner Spring: 40 @ 1-3/4

Valve Stem Clearance: Intake: .002; Exhaust: .003

ENGINE BEARING SPECIFICATIONS

Connecting Rod Bearings:
    Journal Diameter, Inches: 2.0615-2,0625
    Bearing Clearance, Inch: .006-.011
    Rod End Play, Inch: .006-.011
    Rod Bolt Tension: Lbs.Ft.: 45-50

Main Bearings:
    Journal Diameter, Inches: 2.488-2.500
    Bearing clearance: .0005-.0015
    Shaft End Play: .003-.007    (Thrust on Rear Bearing)
    Main Bolt Tension: Lbs.Ft.: 80-85

CAPACITY DATA

Cooling System:
Without heater: 15 quarts; With heater: 16 quarts

Fuel Tank: 17 gallons

Engine Oil: 5 quarts

Transmission: Manual: 2-3/4 Pints; Semi-Automatic Transmission: 3 pints

Rear Axle: 3-1/4 pints

AUTO-LITE DISTRIBUTOR SPECIFICATIONS

Distributor part number: D30: 1GS-4207B-1; D29: 1AP-4103A-1 (distributor rotates clockwise)

Cam Angle, degrees: 39

Breaker Point opening, Inch: .020

Condenser Capacity: .25-.28 Mfds.

Breaker Arm Spring Tension: 17-20 Oz.

Centrifugal Advance: (degrees at RPM of distributor)
    Advance starts: 1 @ 450 RPM
    Full Advance: 10 @ 1425 RPM
Vacuum Advance (degrees @ Inches of Mercury)
    Advance Starts: 1 @ 5-1/2
    Full Advance: 8 @ 14

AUTO-LITE GENERATOR SPECIFICATIONS

Generator Number: GDZ-4801A, GDZ-4801B, GGW-6001A, GGW-6001D, (generator rotates clockwise, 6 volts, Positive Ground)

Generator output: GDZ-4801A, GDZ-4801B: 35 amps @ 2000 RPM; GGW-6001A, GGW-6001D: 45 amps @ 2125

Brush Spring Tension: 35-53 oz.

Field Current at 5 Volts: GDZ-4801A, GDZ-4801B: 1.3-1.5; GGW-6001A, GGW-6001D: 1.4-1.5

AUTO-LITE REGULATOR SPECIFICATIONS

Regulator Number: VRP-4503A, VBE-6001A

Cutout Relay:
    Voltage to close points: 6.5
    Reverse current to open points: 4-6
    Armature Air Gap: .031 inches

Voltage Regulator Setting: 7.3 volts

Current and Voltage Armature Air Gap: .048 inches

Current Regulator Setting: 35 amps; VBE -6001A: 45

AUTO-LITE STARTING MOTOR SPECIFICATIONS

Part number: MCH-6101 (rotates clockwise)

Bush Spring Tension, Ounces: 42-53

No Load Test: 65 amps, 5 volts @ 4300 RPM

Torque Test: 335 Amps, 2.0 volts; Torque: 6.0 ft/lbs.

WHEEL ALIGNMENT SPECIFICATIONS

Caster, Degrees
Limits: -1 to +1
Desired: 0

Camber, Degrees
Limits: 0 to +3/4
Desired: +3/8

Toe-In, Inches: 0 to 1/16

Toe-Out on Turns, Degrees: (If toe-out is incorrect, when other adjustments are correct, look for bent steering arms.)
Outer wheel: 20
Inner Wheel: 20-1/2 to 22-1/2

Kingpin Angle, or Steering Axis Degrees: (If king pin or spindle support angle are incorrect, but camber is correct, look for bent suspension arms or steering knuckle support)
5 to 6-1/2

At our dealership we work very hard to accurately describe our vehicles through text descriptions and elaborate photos. When you purchase a pre-owned vehicle it is not a new vehicle. Any used vehicle can have normal wear and blemishes. Before placing a bid please read the descriptions thoroughly and view all pictures. When bidding or asking questions about our vehicles, your email address may be added to our free newsletter and updates list. If you choose not to receive the free updates, please email us with "REMOVE FROM LIST" as a subject line. We will then remove your address immediately from the list. We do reserve the right to end the auctions early as they are for sale on several other mediums as well.

Included Standard Equipment

Hours of Operation

Mon:
Tue:
Wed:
Thu:
Fri:
Sat:
Sun:

9a - 6p
9a - 6p
9a - 6p
9a - 6p
9a - 6p
9a - 4p
Closed

Vehicle Values

Travel

Vehicle History

Warranty

Warranties are an important part to any vehicle purchase. We have great warranties available for you. Please call us for more information.

Financing

Specialty Auto Financing

J. J. BEST BANC & CO., being the largest Automobile Lender of it's type in the country, is recognized by Antique, Classic, Exotic, Muscle, Hot Rod and Sports car enthusiasts and dealers as the leader in the Classic Car automobile finance industry. Offering long terms and low rates, financing is available for most model cars ranging from 1900 to today. With the most knowledgeable staff available, and loan approvals as fast as 5 minutes J. J. BEST BANC & CO. will help you drive the dream.
PLEASE READ THE FOLLOWING BEFORE YOU CONTINUE…
Thank you for your interest in filing an online loan application.
By clicking on 'CONTINUE', you will be taken to a secured web site to begin filling out the actual loan application form to be forwarded to this dealership.
This application must be completed in its entirety BEFORE you leave the page. It can not be partially completed, or saved for completion at a later time.
You may wish to have the following materials at hand, BEFORE you proceed:
- Information on the Vehicle you wish to purchase.
- Information regarding your Trade-in (if any).
- Personal financial information including date of birth and social security number for you AND your co-applicant (if applicable).
- Personal employment history and current employment information for you AND your co-applicant (if applicable).
- Personal credit references; including names and contact information of each.
- Personal references; including nearest relative not living with you, and their contact information.
Terms: The information you provide on this application will be forwarded to the loan processing department at this dealership, and at the discretion of this dealership, for the purpose of processing this application.

Terms

Payment Types:Certified Funds and Institutional Financing

Fees:Out of State Buyers
Out of state buyers are not charged tax, title, or license, just the documentation fee of $150. The customer is responsible for registering the vehicle in their home state.

Taxes and Fees
In state buyers will be charged state and local taxes, title, registration, and documentary fees. Our documentation fee is $150. All sales transactions must be completed within 5 days of auction close.

Deposit
We require a $1000 deposit within 2 days of winning the auction. Please call the dealership to make arrangements for payment.

Terms:Auction Policies
Customers with zero or negative feedback on eBay Motors please contact us prior to bidding. Otherwise, we reserve the right to cancel your bid. Understand this is only to protect the integrity of the auction. Winning bidder must contact the dealership within 24 hours of the auction close and the purchase transaction completed within 5 calendar days. We reserve the right to re-list or sell the vehicle in the event of a non-paying bidder.

Buyer Pickup
A representative from our dealership can be available for pickup at area airports when necessary. Buyers must schedule pickup prior to making travel arrangements. All of our vehicles are available locally as well, so we do reserve the right to end an auction early at any time for any reason.

Transport

We can help arrange shipping for you, just send us your zip code and we can get you a quote either open or enclosed transport!

Unique Specialty and Classic Cars
1000 South Victory Drive
Mankato, Minnesota 56001

Contact Ken Snow
Phone: 507-386-1726