2000 Cadillac Seville Sls Sedan 4-door 4.6l No Reserve on 2040-cars

Auto blog

New Takata problem results in recall of 414 GM vehicles

An airbag-inflator rupture discovered by Takata during testing has resulted in a new recall affecting 414 vehicles from General Motors, including 395 of them in the US. This latest campaign covers 2015 model-year examples of the Buick LaCrosse, Cadillac XTS, Chevrolet Camaro, Equinox, Malibu, and GMC Terrain. There are no reported breaks in any of these vehicles on the road, and the company estimates only one percent of them actually have the faulty parts. According to documents submitted to the National Highway Traffic Safety Administration (as a PDF), one side-airbag inflator failed a cold test at -40 Fahrenheit "releasing high pressure gas and propelling the separated components apart." The supplier told GM about the failure the next day. In these vehicles, the safety device might not only burst but the bag could inflate incorrectly, as well. GM and Takata say that a cause is not yet known, but they are "conducting an investigation." GM will begin notifying affected owners via overnight mail on Oct. 19. Dealers will replace the side airbag modules on all of the affected vehicles with new components outside of the suspect lot. All of the removed parts will also be collected for further study. Takata's faulty front airbag inflators have resulted in a serious scandal for the supplier. Initial figures indicated 34 million US vehicles are need of repair, though more recent figures have knocked that down to 23.4 million bad parts in 19.2 million automobiles. GM was already among the dozen automakers with models to fix, and some of its pickups were affected, along with the Saab 9-2X and Pontiac Vibe. GM Statement: General Motors is recalling 395 cars and crossovers in the U.S. because one of the front seat side air bags inflators may be defective. In the event of a deployment, the air bag's inflator may rupture and the air bag may not properly inflate. The rupture could cause metal fragments to strike the vehicle occupants, potentially resulting in serious injury or death. GM is unaware of any incidents involving vehicles with these components, which were part of a lot in which one inflator failed acceptance testing at the supplier. Dealers will replace the side air bag module or modules in affected vehicles. Including Canada, Mexico and exports, the total population of the recall is 414, GM estimates 1 percent of the recalled vehicles may have the defect.

GM Design shows what could have been and what might be

We periodically like to check in with GM Design's Instagram account to see what they're cooking up. Even better is when we catch a glimpse of an alternate history of what legendary designers from The General's past were thinking, though those ideas may not have made it into production. This week, for example, the account posted some illustrations from George Camp, whose career at GM spanned nearly four decades, from 1963 to 2001. One of the renderings is of what appears to be a 1971-72 Pontiac GTO Judge, but with two headlights instead of the production unit's quad beams. The rear departs from the canonical version most dramatically, with a massive integrated wing. Other bits that didn't make the production cut include large side vents, a gill-like side marker and rectangular intakes below the headlights that wouldn't be out of place on a modern design today. Amazingly, from what we can make out of the date, it appears that the drawing was done sometime in 1965, which makes it quite prescient.           View this post on Instagram                       A post shared by GM Design (@generalmotorsdesign) There's also a very aerodynamic interpretation of a Corvette ZR-1. To our eyes it splits the difference between the 1986 Corvette Indy concept and a fourth-generation F-body Pontiac Firebird, so perhaps parts of Camp's work on this sketch did make it into physical form. There's also a radical sports car concept from May 1970 that resembles the Mazda RX-500 concept from the same year, a Syd Mead-looking Cadillac coupe, and an Oldsmobile with a cool take on the company's trademark waterfall grille and elements of the Colonnade Cutlass at the rear. Other recent posts include a FJ Cruiser-like off-road EV, a sleek coupe with the Chevy corporate grille, and a rendering of a Silverado-esque pickup that looks far better than the current production version.           View this post on Instagram                       A post shared by GM Design (@generalmotorsdesign) It's pretty easy to lose hours in the account, but it's always fascinating to see GM's visions of what could have been and what might be. Related Video:

Cadillac CT6 uses aluminum to save 200 pounds

In Cadillac's recently launched ad campaign, the luxury brand's tagline is "Dare Greatly," and the two words suggest a brand willing to take big swings, even if they don't always connect. From what the company is promising, the forthcoming CT6 seems like an embodiment of that new motto. With an eventual range of turbocharged engines, reportedly including a turbo V8, a possible plug-in hybrid and streaming rearview mirror, the sedan is certainly pitched as tech showcase. Of course, extensive use of aluminum is practically mandatory to play in the luxury field these days, and Caddy is proving its latest creation can do that too. Despite the weighty appearance of the sedan's squared-off exterior, 64 percent of the CT6 is aluminum, including the entire exterior. Caddy claims that using so much of the lightweight metal sheds 198 pounds off the scales compared to using conventional steel. There still is some steel in the CT6; although it's predominately the high-strength variety. The engineers use the heavier metal for portions around the cabin and B-pillar for added safety. Cadillac also claims using steel "close-out panels" on lower portions of the sedan make the cabin quieter without needing as much sound deadening. The buildup to the CT6's public unveiling has been a long time coming after Cadillac pinned the flagship (for now) sedan's debut at the New York Auto Show nearly a year ago. When the sheet finally comes off on March 31, we get the first good idea about just how great Caddy's latest act of daring really is. Cadillac CT6 Elevates the Science of Mass Efficiency 2015-03-13 Technology DETROIT – Cadillac will use an advanced mixed-material approach for the lightweight body structure of the upcoming CT6 range-topping sedan. The structure is aluminum intensive, but the new Cadillac also includes 13 different materials customized for each area of the car to simultaneously advance driving dynamics, fuel economy and cabin quietness. The CT6 will debut March 31 at the New York International Auto Show and go into production late this year at General Motors' Detroit-Hamtramck assembly plant. "This is the rocket science of automobile construction and manufacturing today," said Cadillac President Johan de Nysschen.