1989 Cadillac Fleetwood Brougham D' Elegance - 63k Miles - All Original on 2040-cars

Auto blog

GM extending warranties on Cadillac CTS-V and Chevy Camaro ZL1 for supercharger issue

Okay General Motors, we've sat by and watched you recall the compact cars, crossovers and pickup trucks, and aside from reporting on it, we've been fairly quiet. This, though, this will not do. We can almost tolerate the recalls on the bread-and-butter cars, but leave the performance vehicles alone.
According to a report from The Car Connection, GM has discovered a problem with the superchargers of the 6.2-liter V8s found in the Chevrolet Camaro ZL1 and the Cadillac CTS-V. Apparently, the issue rests around the internal bearing shaft grease, which can become contaminated (we aren't sure with what). If left unchecked, it'll first lead to a rattle at idle, which goes away under slight throttle. The real warning stage is when a high-pitched squeal develops, signaling that the bearing shaft has failed. Naturally, severe engine damage is the next step (although it's possible that the engine will also just refuse to turnover, although neither case is desirable).
According to TCC, GM will replace the superchargers on vehicles that have exhibited symptoms of bearing shaft failure free of charge. It will also, allegedly, be extending the warranty on all supercharged ZL1s and CTS-Vs to 10 years or 120,000 miles (whichever comes first), from the date of purchase. Officially, only 2009 to 2013 CTS-Vs and 2012 to 2013 ZL1s are suffering from this issue.

GM patent reveals new two-stage turbocharger

Modern turbochargers may be some of the best ever made, but performance is something that engineers are always trying to improve. According to GM Inside News, General Motors (GM) is hoping to alleviate some of the negative aspects of a two-stage turbocharger setup with a newly-patented design. The patent, that was filed on May 19, 2016, reveals a clever bypass system that allows the engine, a four-cylinder unit, to optimize both the low-pressure and high-pressure inlets for its respective functions. According to the filing, a conventional two-stage turbocharger setup is engineered to allow both turbines to operate simultaneously at low and mid engine speeds. At high engine speeds, only the low-pressure turbine works. The setup can't isolate either the low or high pressure side, which can impair low-end performance. GM's new two-stage turbocharger setup looks to eliminate this by linking the high-pressure turbo to the exhaust manifold through the high-pressure inlet duct. The low-pressure turbo is attached to the high-pressure turbo by a low-pressure inlet duct, which is linked to a connecting channel. A single actuator that is housed in the exhaust manifold creates a bypass that can opens the high-pressure inlet or close the connecting channel. Depending on what the engine load and speed is, the ECU guides the actuator—a single rotating spindle with discs corresponding to flanges on the high and low pressure sides—to isolate one of the two turbos. Isolating the turbos allow the respective inlets to be engineered for the best possible fluid dynamic performance. The setup should increase performance and decrease lag. There's no word on what car this setup will make an appearance on, but it will most likely be used in premium vehicles before trickling down to the rest of GM's vehicles. Related Video: News Source: GM Inside News, AutoGuide via GM Authority Cadillac Chevrolet GM Technology Sedan turbo patent engine turbocharging

Reuss says Cadillac CT6-based Buick could happen

Could the upcoming Cadillac CT6 and its Omega platform spawn a Buick variant? According to General Motors' product chief Mark Reuss, it could potentially be in the cards, but "not yet." "We're working on that," Reuss told Automotive News at the 2015 New York Auto Show. While there hasn't been a large, rear-drive Buick on dealerships since the Roadmaster in 1996, the company gave a big hint that it could head in that direction with the Avenir Concept, shown earlier this year at the Detroit Auto Show. As Automotive News explains, a rear-drive Omega-platform Buick could be a real hit in China, where consumers buy 13 Buicks for every one Cadillac. That move would be a big help to GM's bottom line, too, as it'd significantly increase the Omega platform's economy of scale. If a large Buick based on the CT6 were to head to China, though, it likely wouldn't be a simple case of badge engineering (thank God). Reuss hinted to Automotive News that while the mixed-material construction of the CT6 platform "is very flexible," doing an "identical version of that platform or not is a different conversation." What are your thoughts? Should Buick adopt the Omega platform for an Avenir-based sedan? Should that vehicle be sold here in the US, or should it be a China-only offering? Have your say in Comments. Related Video: