2010 Cadillac Cts Luxury Sedan 4-door 3.6l Luxury Edition on 2040-cars

Auto blog

Meet the mother-daughter team that's worked on almost every Chevy Volt

It's Mother's Day, and we're soft enough we love our mothers enough to share a new video from General Motors with you. In it, we meet Monique Watson (left) and Evetta Osbourne, a mother-daughter team that works at the Detroit-Hamtramck Assembly where GM makes the Chevy Volt (along with all of GM's other plug-in hybrids: the Opel Ampera, Holden Volt and Cadillac ELR). The two work side-by-side and have installed the lithium-ion battery pack on almost all of those vehicles - nearly 80,000 of them - since GM started making the pre-production Volts in 2009. In a prepared statement, Watson said that she likes working next to her mom, day in and day out, and they the two are totally in sync when it comes to putting the 400-pound, 16.5-kWh packs into the vehicle undersides. They two can also share stories throughout the day, and Watson said, "The arrangement has absolutely improved our relationship." Osborne started working at Detroit-Hamtramck in 1999, Watson since 2006. If you're driving a Volt today, you probably have them to thank for doing a bit of the work putting your car together. See a short video of them in action below. It's Always Mother's Day for Detroit-Hamtramck Duo Mother, daughter install lithium-ion battery pack in nearly all GM electric vehicles 2014-05-08 DETROIT – For Detroit resident Evetta Osborne, every day is Mother's Day. That's because she literally works side by side with her daughter, Monique Watson, at General Motors' Detroit-Hamtramck assembly plant. They have installed the lithium-ion battery pack on nearly every Chevrolet Volt, Opel Ampera, Holden Volt, and Cadillac ELR since production began. In fact, apart from vacation days and an occasional sick day, the mother-daughter duo has installed almost every battery pack since the Volt was in pre-production in 2009. The ELR launched earlier this year. All told – including Ampera – that's more than 80,000 electric vehicles. "We're a good team and our relationship is secondary when it comes to performing our jobs – but it's great to work alongside my daughter, said Osborne, a mother of five. Because the battery packs weigh more than 400 pounds each, automatic guided vehicles – robotic carts that use sensors to follow a path through the plant – deliver them just as the vehicle body structures glide into position overhead. The carts then lift the T-shaped packs, and Osborne and Watson guide them into the chassis and secure each one with 24 fasteners.

Weekly Recap: Car-pedestrian crashes remained elevated in 2014

The death of American Horror Story: Freak Show star Ben Woolf served as a reminder this week that car crashes involving pedestrians remain a problem, and a new study issued on Thursday reinforced that the situation isn't really getting better. The Governors Highway Safety Association found a slight decline, 2.8 percent, in the number of pedestrian deaths in the first six months of 2014. Fatalities dropped from 2,141 to 2,125 compared with the same period in 2013, though the association says it's a statistical wash when factoring in undercounting. Deaths are still 15-percent higher than in 2009. "The number of deaths remains relatively high and is cause for concern," wrote Allan Williams, who compiled the report and is the former chief scientist at the Insurance Institute for Highway Safety. This is the first look at data from last year, and the National Highway Traffic Safety Administration will issue its full-year results later. The GHSA found some progress on the roadways, as 24 states and the District of Columbia reported drops in pedestrian deaths. In some states, the problem isn't even a problem at all: Nebraska and Wyoming reported one fatality apiece, though large population centers in urban areas are where most accidents occur. "This is a clearly a good news, bad news scenario," Jonathan Adkins, GHSA executive director, said in a statement. "While we're encouraged that pedestrian fatalities haven't increased over the past two years, progress has been slow." Other News & Notes Cadillac previews CT6 during Oscars Cadillac previewed its upcoming flagship sedan, the CT6, in commercials that aired Sunday during the Oscars. As expected, the creased sedan carries on Cadillac's recent design language, and the car in the commercial looks like a larger version of the CTS and ATS sedans. The CT6 will be revealed this spring at the New York Auto Show and launch late this year. It will be assembled at General Motors' Detroit-Hamtramck factory on a rear-wheel-drive chassis, and the CT6 is the first car to use Cadillac's revised alpha-numeric naming scheme. The commercials also kicked off Cadillac's "Dare Greatly" campaign, which is the first with its new advertising agency, Publicis Worldwide. Honda unexpectedly changes CEOs Honda unexpectedly announced this week that it will change CEOs. Current chief Takanobu Ito will step down in June and be replaced by company veteran Takahiro Hachigo.

2016 Cadillac CT6 to get an aluminum body?

Well this is interesting: A hot-off-the-press report in Automobile claims the coming Cadillac CT6 will have an aluminum body. Most write-ups on the CT6 claim it will have a body that's a combination of aluminum and high-strength steel - Automobile itself wrote of "high-strength steel, aluminum, and steel stampings" in October. An all-aluminum body would be quite the reversal, contradicting the last four months of reportage and company statements on the matter. Mark Reuss, EVP of global development at General Motors, told The Detroit News in October, "We will create with the CT6, the world's most advanced body structure... [and] it's not aluminum. It's a stronger, smarter, safer premium luxury vehicle." It echoed the earlier Automobile story in saying the CT6 would use GM's "patented welding technology with high-strength steel, aluminum and steel stampings and castings." That same month, the Wall Street Journal ran a piece titled, "GM Won't Follow Aluminum Strategy in Future Cars," in which Reuss said, "making big statements around all carbon fiber, all aluminum, all magnesium, they're very interesting," and that GM wouldn't be doing it. That piece also circled back to a material mix and GM's special welding process, saying the CT6 "will have a body made of aluminum, high-strength steel and other materials, and will be 100 kilograms (220 pounds) lighter than a similar-sized car made of high-strength steel." We don't know what kind of body Cadillac's new assault on luxury is going to wear, but now we can't wait to find out. Featured Gallery Cadillac Elmiraj Sedan: Spy Shots View 22 Photos News Source: AutomobileImage Credit: Chris Doane Automotive Cadillac GM Luxury Sedan aluminum cadillac ct6