1974 Cadillac El Dorado Triple Black Coupe This Car Has Attitude on 2040-cars

Auto blog

Expect the Cadillac XT3 small crossover in late 2018

Cadillac's sedan-heavy lineup can't complete in this crossover-crazy market, it seems. The Detroit News spoke to Cadillac boss Johan de Nysschen and found out some more details about the brand's plan to alter its lineup to cater more to current consumer tastes. It's no surprise that these plans would include a small crossover, because de Nysschen has been talking about a vehicle smaller than the XT5 like this since at least 2015. The report also pins the Fairfax Assembly Plant, where GM builds the Buick LaCrosse and the Chevrolet Malibu, as the site for what could be called the XT3's production. That's not an immediately obvious choice, since the LaCrosse and Malibu are based on the latest evolution of the Epsilon platform, known as E2XX. And the XT5 is based on a crossover version of that same platform (known as C2XX), while XT3 is expected to be smaller than the XT5. So perhaps there's a different assembly line going into Fairfax, or the C2XX platform can be significantly shortened. We assume that the XT3 would be built on a smaller platform, perhaps the Gamma II that underpins the Chevrolet Trax and Buick Encore – which are built in either South Korea or Mexico, depending on which market they are to be exported to. The Encore is selling very well for Buick, with sales figures increasing through late last year. Another possibility is the D2XX platform that underpins the Chinese-built Buick Envision and the GMC Terrain and Chevrolet Equinox, perhaps with assembly happening at the CAMI plant in Ontario. At this early stage, without confirmation of GM as to what platform the XT3 will use or where it will really be built, it's too early to say what the Fairfax rumor means. This isn't the first time we've heard about a small Cadillac crossover. Back in 2015, de Nysschen told us to expect it sometime in 2018. But later that year, speaking to Reuters, he posited that it'd be closer to 2019. The Detroit News says de Nysschen told them it'll launch in the second half of 2018, splitting the difference between what we'd heard previously. Remember, Cadillac's only two vehicles in the segment are the XT5 and Escalade. We know that the brand is almost certainly scrambling to fill the holes in that side of the lineup. We think a three-row crossover will slot between the two, probably called the XT7.

2016 Cadillac ATS-V First Drive [w/video]

If you get hot and bothered for hot-rodded sedans and coupes, you probably know that Germans have long dominated that cutthroat scene. For years, the Audi RS/BMW M/Mercedes-AMG triumvirate has ruled the microcosm of grunty, mid-level luxury cars. But a funny thing happened when Cadillac's first V car hit the market in 2004. Since the CTS-V crashed the high horsepower party, German tuning houses started thinking less about the "Daddy's Caddy" stereotypes and more about the next imminent threat – in this case, the inevitable high-horsepower spinoff of the smaller, nimbler Cadillac ATS. The standard ATS' defense against the German triad hasn't been triumphant so far (GM's Michigan plant was idled for three weeks in 2014 due to excess inventory), but the souped-up 2016 Cadillac ATS-V presents a fresh bid to put the Teutonic competition on alert. The ATS-V's flared bodywork and quad exhaust pipes offer bits of visual shock and awe, but significant hardware upgrades back up the go-fast looks. Front and center is a twin-turbocharged, 3.6-liter V6 with reworked internals including a charge-air cooler, titanium connecting rods, and titanium-aluminide turbines. The new engine produces 464 horsepower and 445 pound-feet of torque, up a staggering 262 hp and 173 lb-ft compared to a base, four-cylinder ATS. Those output figures eclipse the BMW M3/M4 (425 hp, 406 lb-ft) and Audi RS5 (450 hp, 317 lb-ft), but lag slightly behind the V8-powered Mercedes-AMG C63 (476 hp, 479 lb-ft), and more so the C63 S (503 hp, 516 lb-ft). The chassis benefits from several structural braces, most notably a shear panel intended to boost front-end stiffness. Extra poundage from the add-ons are minimized through lighter-weight materials – in the case of the shear panel, stamped aluminum. Cadillac says though it intended to make the ATS the quickest car in its segment (stated 0-60 mph times between 3.8 and 3.9 second virtually match the BMW M4 and Mercedes-AMG C63 S' 3.9 figure), the development team says they also focused on subjective qualities like turn-in quickness and steering response. As such, toe links have been replaced with ball joints, mounts have been retuned, and reworked magnetic damping offer greater responsiveness. Six suspension bushings have been stiffened and ten have been completely redesigned, and the Performance Traction Management system that tames beasts like the Corvette Z06 and Camaro ZL1 also helps lay down power in the ATS-V.

GM and Ford quarterly sales continue to slump in China

BEIJING — General Motors and Ford announced their quarterly sales in China fell, albeit at a slower pace sequentially, as the U.S. automakers were hit by a slowing economy amid the Sino-U.S. trade war. GM's vehicle sales in China for the quarter ended June 30 dropped 12.2%, while Ford's sales slumped by 21.7%. While GM also suffered from heightened competition in its key mid-priced SUV segment, Ford was hurt by the limited new models for customers to choose from. For the first quarter of this year, Ford's sales in China tumbled 35.8 percent while GM's skid 17.5 percent. Still, the numbers from GM, the second biggest international automaker in China by sales, and Ford portend more uncertainty for the industry which is trying to rebound from a downward spiral that led to its first annual sales decline last year in more than two decades. GM delivered 1.57 million vehicles in China in the January-June period this year, while Ford delivered 290,321 vehicles. China's factory activity shrank more than expected in June, highlighting the need for more economic stimulus amid higher U.S. tariffs and weaker domestic demand. Annual car sales in China fell last year for the first time since the 1990s, and they are expected to fall this year too. Sales tumbled 16.4% in May from the same month a year prior, the China Association of Automobile Manufacturers (CAAM) said. That marked the 11th consecutive month of decline and followed falls of 14.6% in April and 5.2% in March. U.S. car companies' share of total China passenger vehicles sales fell to 9.6% in the first five months of this year from 10.9% in the year-ago period, according to CAAM. Over the same period, German car makers' share has risen to 23.3% from 20.9% and Japanese auto makers' to 21.3% from 17.3%. CAAM is set to announce June sales next week, which industry analysts forecast will be negative.   New models In China, GM has a joint venture with SAIC Motor Corp, in which the Buick, Chevrolet and Cadillac are made. It also has another venture, with SAIC and GuangxiAutomobile Group, in which they make no-frills minivans and have started to make higher-end cars. Sales of GM's affordable brand Baojun dropped 31.8% for the latest quarter. But luxury brand Cadillac's sales jumped 36.6%. GM sold 3.64 million units in China last year, down from 4.04 units in 2017. Ford makes cars in China through its joint venture with Chongqing Changan Automobile Co and Jiangling Motors Corp (JMC).