1960 Buick Lesabre Convertible ,survivor ,runs Great ,easy Restoration ,low Res on 2040-cars

Auto blog

2017 Buick LaCrosse an evolution of sharp Avenir concept

After years as a bloated, uninspiring, but comfortable near-premium sedan, Buick has taken the wraps off a leaner, lither, far more stylish LaCrosse. The third-generation model has just made its debut at the 2015 Los Angeles Motor Show. While there's a lot to talk about, let's first address the new, Avenir-inspired sheetmetal. The fascia is basically the concept car smoothed over into production form, featuring the same winged trishield. In place of the chrome-trimmed waterfall, the LaCrosse gets a blacked-out, recessed grille with a chrome surround. It looks good in photos but it's better in person, adding a real sense of complexity and depth to the front end. The headlights and lower fascia, meanwhile, adhere closely to the concept. The same cannot be said of the LaCrosse's tail. While the taillight lighting pattern is similar, the overall shape of the lighting element is radically different, refining the design featured on the back of the Regal. Also gone, sadly, is the Avenir's boattail rear deck. Instead, the LaCrosse gets a small rear deck that curves up into a pleasant duckbill spoiler. The rest of the tail is pleasantly restrained. Perhaps the weakest point is the profile, where Buick has instituted a "split-spear" design, featuring a strong shoulder line above the rear wheel well, which sits below an even stronger character line that curves down and towards the front of the car. It strikes us as just a little too much, like the Impala. Underneath that sheetmetal, Buick has managed to trim nearly 300 pounds of body fat, nearly half of which came from the vehicle's actual structure. That 300 lbs, according to Buick's engineers, is equivalent to a Kenmore side-by-side refrigerator, in case you needed a helpful comparison. Despite the weight savings, Buick has upped the torsional rigidity for this new model by 15 percent. The LaCrosse's cabin features a strong, cockpit-like design, with a high, floating-bridge center console. This is possible due to Buick's adaption of the Electronic Precision Shift system, introduced earlier this month on the new Cadillac XT5. Despite the new-fangled console design, Buick's retained the wraparound cabin style introduced on the second-gen model. Based on a quick crawl around the interior, space is great in front, although ingress in back is somewhat difficult due to the roofline. You're probably wondering why we haven't said anything about the mechanicals just yet.

Buick Enspire spied for the first time, loses concept's electric powertrain

About a year ago, Buick showed a high-performance electric crossover with wide, aggressive, curvy lines that was called the Buick Enspire. Now we have our first look at the production version. While it does seem to be styled like the crossover, it also seems to have lost its electric powertrain in favor of internal combustion. At the front of the crossover, we can clearly see it has the skinny, scowling headlights of the concept sitting high on the front fascia and flush with the hood. The main grille looks like it may be smaller, but it could also just be that the actual open section of the grille doesn't fill up the grille area of the fascia. In profile, the crossover has an attractive long nose, low roof and rising belt line. The rear shows the most change, as the rear pillars are much thicker, and the taillights don't appear to span the full width of the crossover. It's in the rear that we can also see the evidence that the Buick Enspire will actually be gasoline powered. Looking very closely under the rear bumper cover, we can see two exhaust tips turned to face the ground. Based on the size of the crossover, and the fact a Cadillac XT4 was being driven along with the prototype, the Enspire is probably using the XT4's platform, as well as its mechanical bits. That means it probably has a turbocharged 2.0-liter four-cylinder making 237 horsepower and 258 pound-feet of torque. Power will also probably go through a nine-speed automatic to either the front wheels or all four. This prototype looks to be pretty far along, so we'll probably see the production version in about a year. Considering the Enspire's size and likely powertrain, it may even replace the similar Buick Envision. And since the Envision is Buick's worst selling crossover (unless you count the Regal TourX as one), it would be ripe for replacement.

GM cutting Chevy Sonic, Buick Verano production [UPDATE]

UPDATE: A previous version of this story indicated that Orion Assembly would be idled for seven weeks, from February 16 through April 6. This was incorrect. The factory will instead only be idled for the weeks of February 16 and April 6. The story has been edited to reflect this. General Motors has announced that the factory responsible for the Buick Verano and Chevrolet Sonic will be idled for the weeks of February 16 and April 6, with blame being placed on excess supply. The Orion Assembly plant, about 45 minutes north of GM's Renaissance Center headquarters, employs about 1,800 people, but they'll be given a pair of furloughs as inventories of the sub-compact Sonic and premium compact Verano reach 127 days and 84 days, respectively. That works out to 26,600 Chevys and 9,800 Buicks waiting for buyers. According to Automotive News, the compact Chevy sales bested the industry average in 2014, jumping up nine percent versus the the overall segment's eight-percent gain, while the Buick sedan's sales were down four percent. When asked about the shutdown, a GM spokesman told AN that it will "build to market demand," while also pointing out that the company did not comment on production plans. News Source: Automotive News - sub. req.Image Credit: Bill Pugliano / Getty Images Plants/Manufacturing Buick Chevrolet GM buick encore orion assembly