2000 Bmw Z3 Roadster Convertible 2-door 2.8l on 2040-cars

Auto blog

2013 Dinan S3 BMW 550i

Steve Dinan has been enhancing BMW models since 1979. But don't throw his company into the ring with the dozen or so other tuners who tweak, tinker and piggyback upgrades on the famed German marque. Dinan is a tuner, but it's also an engineering firm that writes its own software, builds its own parts and then backs everything it does with a factory-grade warranty. That sort of fastidiousness comes at a price, but most of its customers - including the powerhouse of BMW Motorsport - rely on Dinan to help them come out on top.
In stock form, BMW's 550i is a formidable four-door with a twin-turbocharged 4.4-liter V8 rated at 400 horsepower and 450 pound-feet of torque. While those figures allow it to run with quick company (0-60 in 5.0 seconds, according to the automaker), Dinan puts the sedan's kettle on full boil with its S3 package. Starting with the engine, the performance engineering firm bolts on larger turbochargers, air-to-water intercoolers, a trick strut tower brace cold air intake, a quad-pipe free flow exhaust and its own engine management software. Pump in some premium fuel, and the result is 542 horsepower and 587 pound-feet of torque. Power is sent through the stock eight-speed automatic to a limited slip rear differential (Dinan will upgrade xDrive all-wheel drive models, too).
The Dinan S3 also features and extensive suspension upgrade that includes new front camber arms and low compliance rear control arms (engineered to reduce understeer and improve turn-in). The stock dampers are retained, but new bump stops are installed along with new springs. Overall, the car rides about a half-inch lower than stock to improve roll rate. To reduce unsprung weight, forged 20-inch HRE Performance wheels are fitted at all four corners (wearing Michelin Pilot Super Sport tires - 275/35ZR20 up front and 295/35ZR20 in the rear). Lastly, the company remaps the factory Electronic Damper Control (EDC) software with its own Dinan Shockware to work in conjunction with the new enhancements.

2015 BMW M4 Convertible is here to put wind in your sails

Each generation of the BMW M3 has included a convertible model. Even the distant E30, the patriarch of the M3 line, had an ultra-rare (only 787 were built) droptop model. The convertible became more common on the successive generations, with the hardtop-convertible E93 being the most recent. Considering this history, there seemed very little doubt that as the M3 became the M4, a convertible would be in the cards. Now, the new droptop has arrived.
Set for its global debut at the 2014 New York Auto Show, the 2015 BMW M4 Convertible features, like its forbearers, everything that's great about the hardtop variant while adding an unlimited amount of head room. That means the same 3.0-liter, 425-horsepower, 406-pound-foot, twin-turbocharged straight six sits under its domed hood, while either a six-speed stick or a seven-speed M dual-clutch transmission dispatches power to the fat rear tires.
As for specific differences between the hardtop and the new convertible, obviously, the droptop is heavier. A lot heavier. Where an M4 with a six-speed manual tips the scales at 3,530 pounds, the M4 Convertible weighs in at 4,055 pounds. Believe it or not, BMW has actually trimmed 90 pounds from the last-generation M3 convertible, code-named E93. This marginal weight reduction from the third-generation convertible to the fourth is barely half of the 174 pounds BMW was able to subtract when transitioning from M3 Coupe to M4 Coupe.

BMW considering North American engine plant?

BMW may be set to expand its US operations with a new engine plant, Bloomberg reports. The Bavarian automaker already has its Spartanburg, SC factory which builds the company's X3, X5 and X6 crossovers. According to the story, Mexico is also under consideration for the BMW engine factory, with the report claiming a final decision will be made in 2014.
"Establishing local motor manufacturing abroad is more complex than assembling cars, but it's a logical step for them to eventually start making engines in markets where they're expanding vehicle production," Juergen Pieper, an analyst for Bankhaus Metzler tells Bloomberg. Building engines in the US or Mexico would save BMW from having to ship engines for some of its most popular models across the Atlantic.
BMW, for its part, hasn't said anything concrete. Spokesman Mathias Schmidt is quoted in the story saying, "As part of our long-term growth strategy, we're frequently looking at different countries for possible locations of future production facilities. No decisions have been made yet, though, for an additional plant."