Bmw 528i 1999 Titanium Silver Metalic, Low Mileage, Excellent Condition on 2040-cars

Auto blog

Why are all US-bound BMW i3 EVs with range extenders stuck at port?

The first BMW i3 EVs have been delivered in the US, but in a quirk of the rules, none of them have been the range-extended versions. Long-time BMW electric vehicle driver Tom Moloughney discovered this fact the hard way. His i3 REx has been sitting at a New Jersey port for over a week and he's getting impatient. The problem is something Moloughney calls a "Monroney Hold." So, instead of sitting there fuming, Moloughney did a bit of research and discovered that the problem is something he calls a "Monroney Hold." He says that "the EPA certification has not been completed so BMW doesn't have a Monroney label (window sticker) to post in the window before the car leaves the port, which is required by law. The range extender option changes (shortens) the car's electric range, and also requires an official MPG rating so BMW couldn't use the same Monroney label as they did for the all electric i3." You can read more on his website, but it turns out that the story isn't so simple. For one thing, the EPA testing has been finished. Washington State representative Chad Magendaz told Moloughney that he asked the EPA for an official statement and got the following from Linc Wehrly, Director of the Light-Duty Vehicle Center Compliance Division: "EPA tested the i3 REx and provided the results of that testing to BMW on May 13th. EPA is not aware of anything that would prevent BMW from importing the vehicles since May 13th." Then there's the official word from BMW. Spokesman Dave Buchko told AutoblogGreen that: We are moving as quickly as possible to release the first BMW i3 Range-Extender models to BMW i Centers. Receipt of test data from the EPA is one step, but not the final step, in the process of receiving certification from the EPA. Rules do not permit the release of vehicles for sale until EPA labels are finalized, produced and affixed to any vehicle. Barring any unforeseen delays, we expect that to happen by the end of this week. We have never certified a vehicle like this before. We are taking every precaution to make sure that everything is done in a timely, but more importantly correct manner. In that Monroney labels cannot be produced until the EPA certification process is complete, the characterization [of a "Monroney Hold"] is not technically incorrect, but there is more to it than that, as is often true in life. On a lighter note, BMW donated a loaded i3 to Brad Pitt's Make It Right charity foundation as a fundraiser. Read about that below.

Meet the inventor of the BMW 3 Series wagon

It's hard to imagine, but once upon a time, there were only two BMW 3 Series variants: the coupe and sedan. Back before gran coupes, convertibles and yes, even touring models were available, buyers could only get their 3 Series fix if it came with two or four doors and a fixed roof. Back in the mid '80s, BMW engineer Max Reisbock was having some trouble fitting his whole family into his four door. Rather than suck it up and buy a van, he picked up a wrecked 3 Series and got to cutting in a buddy's garage. Months later, he had the very first 3 Series Touring ever built.
At first, he kept the the car to himself, using it to haul friends and family around, but he eventually showed it off to his friends at work. When the BMW executives found out about his project, they called him up to take a closer look. After putting an eyeball on the car, they took it, copied his design, made a few tweaks and quickly rolled out the first production 3 Series Touring. How's that for validation? Check out the video below for Reisbock's story.

2014 BMW R NineT

BMW is taking a page from the Harley-Davidson playbook with its groundbreaking R NineT. A retro cafe racer with an urban hooligan twist, the bike is fully customizable from fork to exhaust. Of course, any motorcycle can be customized, but the fact that BMW has built its newest bike to encourage modification using parts that can be swapped with simple tools is a radical move for a motorcycle maker best known for its plug-and-play touring bikes.
To underscore exactly how radical, BMW has even partnered with custom heavy-hitter Roland Sands Design, which developed the initial concept for the bike and is now manufacturing a full line of parts and accessories for the R NineT, including radial valve covers ($950), retro racing saddles ($400-$420), radial gauge housing ($400) and a radial headlight bezel ($250), among other things, all of which can be swapped with a socket wrench or screwdriver instead of a hacksaw, wire cutters and TIG welder.
Alas, the bike I tested for two weeks was stock, so consider it a blank canvas.