2004 Bmw 545i Sport Package 6 Speed Manual Black On Black Low Miles Rare Find on 2040-cars

Auto blog

BMW says yes to 1 Series M successor, no to M6 Gran Coupe with xDrive

If you're anything like us, the first half of that headline made you smile. The BMW 1 Series M Coupe was, without a doubt, one of our favorite cars from the past few years, and according to a BMW Blog interview, Dr. Friedrich Nitschke, head of the company's M division, has confirmed that a successor is in the works.
"We haven't made a decision yet, but the 1M coupe was so successful, that in my opinion, I am absolutely sure we will build a successor," Nitschke told BMW Blog. Currently, BMW only offers the M135i version of the new 1 Series hatch in Europe, which Nitschke says is "not a pure M car."
Moving elsewhere in the M range, BMW Blog asked about the M6 Gran Coupe that recently debuted at this year's Detroit Auto Show. The obvious competitors for this car will be higher-power versions of the Porsche Panamera and Audi RS7, but while both of those offer all-wheel drive, the M6 only sends power to its rear wheels.

BMW 1 Series prototype packs direct water injection

Just a few months ago, BMW showcased an M4 that was modified to serve as the safety car for the MotoGP racing series. The flashing lights and emergency equipment, however, weren't the only modifications BMW made to the performance coupe. It also packed an innovative new water injection system. And now it's furthering the development of that system by running it in a 1 Series hatchback as well. Revealed at the BMW Group Innovation Days 2015 event, this five-door 1 Series packs a three-cylinder gasoline engine – like the one found in a Mini or i8 – but fitted with the direct water injection system. In this application, the system sprays a fine mist of water – yep, regular old H2O – right into the combustion chamber. While mixing water with gasoline normally wouldn't be recommended, in this case it evaporates immediately and helps cool the engine from the inside, allowing it to run at higher efficiency. That cooler running engine brings with it several benefits. It delivers improved fuel economy and lower emissions, to start. It also allows for an earlier ignition point, higher compression ratio, and higher boost pressure in turbocharged engines, delivering increased output. It even cuts down on engine knocking (where combustion occurs spontaneously), reduces wear and tear on the engine, and makes better use of lower octane levels. If that sounds like a win-win-win... win (we're losing count of all the wins here), it's because BMW just may be on to something. Of course it does require a water tank to be fitted on board, which means added weight, but instead of requiring the driver fill up the water tank, BMW has fitted this prototype with a system that replenishes the water level from the air conditioning system when the vehicle is switched off. So unless it's being driven in a particularly extreme climate, it doesn't even need topping up. Add one more "win" to the list, then. Extra power, improved real-world fuel economy: Direct water injection enhances efficiency. With direct water injection for turbocharged petrol engines, the BMW Group has again succeeded in enhancing the capabilities of conventional engine technology through an ongoing process of refinement and improvement. The precisely controlled injection of water into the engine cylinders produces a cooling effect that boosts power and torque, particularly when operating at or near full throttle, while at the same time reducing fuel consumption and emissions.

BMW invests in carbon fiber for use beyond i and M models

The immense amount of resources BMW has poured into its i brand program hasn't stopped, and recent developments indicate it's likely to pay off for BMW and BMW buyers outside the i brand. The i8 has already sold out its first year run, the i3 racked up 10,000 orders before it even went on sale and is already the subject of public discussion about being stretched into an i5, and a new investment in carbon fiber production has the automaker talking about CFRP use in non-i and non-M models.
BMW and SGL Group got together to form SGL Automotive Carbon Fibers (ACF), and the joint venture produces all of the CFRP for the i3 and i8 on two production lines at its plant in Moses Lake, Washington. After already investing $100 million to increase capacity, BMW has announced that another $200 million will add four more production lines, tripling production from 3,000 tons per year to 9,000 tons. When the expansion is complete in 2015, BMW says the Moses Lake facility will be the world's largest carbon fiber plant.
That's a lot of weave and the long view is that it will find its way into core models, with BMW exec Dr. Klaus Draeger saying, "As part of an intelligent mix of materials, we will apply carbon also beyond our BMW i and BMW M models in the future," and be able to do so "at competitive costs and in large quantities."