2024 Audi S8 / Rear Seat Comfort Package / Executive Pkg! on 2040-cars

Auto blog

Audi A3 Clubsport Quattro concept bringing its 525 horses to W?rthersee

It's almost late May, and you know what that means: the last of the snow has melted, the Stanley Cup playoffs are in full swing, the flowers are blooming, and the performance-car faithful are descending on Wörthersee in Austria for the annual GTI-Treffen.
Not only is the Wörthersee Tour (as the automaker calls it) a chance for enthusiasts to show off their rides, it's also a prime opportunity for the Volkswagen Group to show some of its most dedicated customers what it can do. Past meets have given us such notables as the Audi A1 Clubsport Quattro, Volkswagen GTI W12-650 and Skoda Fabia RS 2000 Roadster, to name just a few. And now Audi has emerged as the first VW Group brand to reveal what it has in store.
It's called the A3 Clubsport Quattro, and seems to offer a pretty clear indication of what we should expect of the next RS3. The concept is based on the S3 sedan, but swaps out its 2.0-liter turbo four for a retuned version of Audi's sweet 2.5-liter turbocharged inline-five, retuned to produce a massive 525 horsepower and 442 pound-feet of torque.

Audi considering other variants, turbo V6 for R8

More details from the Audi R8 event at Spain's Ascari circuit have met the Internet, and they provide more intel on the supercoupe will evolve over the second generation. First, they note some small differences in stance with this new car, being wider than the current car and sitting 30 millimeters (1.18 inches) lower. Compared to its Lamborghini Huracan brother, it gets three extra centimeters in the wheelbase. Filling out the power numbers, the 'entry-level' V10 engine at launch rolls out 540 horsepower and 399 pound-feet of torque, does the 0-60 mile per hour dash in 3.5 seconds, and hits a top speed of 200 mph. The V10 Plus model rocks 620 hp and 412 lb-ft, which slices 0.3 seconds off that acceleration time and adds five more mph to the top speed. They'll transfer their power through a seven-speed S-tronic that shifts faster than before, and it will in turn send power through an electronically-controlled clutch at the front axle and a constantly variable limited-slip differential at the rear axle. The power split is said to default to 42/58 front-to-rear, but 100 percent of the torque can be sent fore or aft. Benchmarked against the 991-series Porsche 911, driving sensations travel through an electromechanical steering setup that can be had with a variable rack if preferred, leading to standard 19-inch wheels with the option of 20-inchers and tires developed specifically for this car. A Performance setting offers dry, wet, and snow modes; that first setting turns the ESC off except for situations of impending doom, and Audi racer and test driver Frank Stippler told Top Gear that understeer is reduced, to which TG added "it oversteers at will." Stippler said it's "a lot closer to the GT3 race car than ever before," and even though it's "a lot" less intense than the Huracan, it's just as fast on the track. His estimate is that the new R8 will lap the Nurburgring between ten and 15 seconds faster than the current car. R8 technical lead Roland Schala said the new chassis opens up new avenues of development because "there's no problem to change it," mentioning models like a Clubsport or Superleggera as no longer forbidden. Differentiation could come from a wider engine mix, too. Markets like China need smaller displacements, so Audi's twin-turbo V8 is expected to join the line-up at some point, bringing 500 horsepower.

Researchers halfway to cutting carbon fiber costs by 90%

Carbon fiber has been utilized for decades to build racecars, as a means to cut weight while maintaining strength. But until recently, the space-age material has been largely absent from the street on anything but supercars because of the expense to use it. Recently, BMW signaled a major shift in that trend when it starting using carbon fiber reinforced plastic panels on the i3 and i8. This relatively small scale start might be just the beginning; the German company believes that a breakthrough to inexpensively manufacture the lightweight stuff is just on the horizon.
MAI Carbon Cluster Management GmbH counts BMW, Audi, Airbus, the German government and many other organizations as supporters, and it's researching how to make carbon fiber cheaper to produce, according to Automotive News Europe. The company thinks it can reduce costs by 90 percent in the near future. "We've certainly reached a halfway point on our cost-cutting target for suitable carbon-fiber parts," said project head Klaus Drechsler to Automotive News Europe.
Unfortunately, it isn't entirely clear just what MAI Carbon is doing to make such a huge leap possible. However, a recent post on the company's website talks about a new form a carbon fiber using a thermoplastic matrix that could be cured in less than three minutes. That's compared to about 90 minutes in the traditional process with an autoclave.