2008 Acura Tl on 2040-cars

Auto blog

1997 Acura SLX gets 350 actual Acura horsepower for Radwood

For the Radwood Orange County, Calif., car show, a show themed around 1980s and 1990s cars, Acura is bringing a variety of its original models including a 1991 NSX and a 1986 Integra. The company is also bringing something obscure, a 1997 Acura SLX, the brand's first SUV, offered from model years 1996 to 1999. In some ways, it's something Acura might not want to highlight, since it's really a rebadged Isuzu Trooper, just as the original Honda Passport was a rebadged Isuzu Rodeo. But this SLX is special; it has real Acura power under the hood. The project was led by Acura engineers and Pikes Peak racing drivers James Robinson, Paul Hubers and Jordan Guitar, and the frame and body restoration as well as the powertrain swap was done entirely in-house at Honda R&D in Ohio, according to Acura rep Andrew Quillin. The team pulled out the original naturally aspirated 3.2-liter V6 that made just 190 horsepower and 188 pound-feet of torque, and dropped in a turbocharged 2.0-liter inline-four from a new Acura RDX. That engine also received a new intake, exhaust, turbo and ECU tune, which brought power up to an estimated 350 horsepower and 340 pound-feet of torque, similar to the Graham Rahal Performance RDX. Not only that, but the old-school four-wheel-drive system and live rear axle were dropped in favor of the RDX's indpendent suspension and torque vectoring "Super Handling All-Wheel Drive." "Dropped in" is a mischaracterization, though, as Acura had to weld new subframes front and rear to the existing frame to get the transverse engine and modern suspension to fit. Acura was careful to keep the SLX looking as close to the original as possible. On the outside, Acura repainted the SLX in a modern red paint available on the RDX, but retained the champagne lower moldings. The stock wheels were replaced with 17-inch Fifteen52 wheels, but they have a very similar design and finish to the original wheels. A hard-shell spare tire cover was added, and a simple "SH-AWD" badge on the back is the only hint at what's under the body. The interior was restored at the company's L.A. design studio, where the upholstery was redone in a gray "gathered" leather like you would have seen when it was new. A bit of gray wood trim updates the interior slightly. The RDX's push-button starter and shifter buttons have been added to the center console, shift paddles behind the original steering wheel, and an aftermarket instrument cluster mounted to the steering column.

Honda marks 20 million vehicles made in the USA

Japanese automakers manufacturing in the United States is nothing new. But it was in November of 1982 when the first Honda Accord rolled off the assembly line in Marysville, OH. It was the first Japanese vehicle assembled in the US, and in the nearly 32 years since, Honda has made 10 million Accords here for a total of 20 million cars manufactured in America - enough to span from New York to San Francisco twenty times. It's that double landmark which Honda is now celebrating.
Honda has come a long way in those three decades, keeping that original plant in Marysville on line while expanding to three more - in East Liberty, OH; Lincoln, AL; and Greensburg, IN - with a fifth plant (the Performance Manufacturing Center) opening on the same site in Marysville to build the Acura NSX next year. It also builds engines in Lincoln and in Anna, OH, and automatic transmissions at Russells Point, OH, and Tallapoosa, GA.
Between those seven sites, Honda produces 11 different models, including the Accord, Civic, Crosstour, CR-V, Pilot, Odyssey and Ridgeline as well as the Acura ILX, TL, RDX and MDX. Production keeps on ramping up as Honda produced a record 1.3 million vehicles in the US last year, 95 percent of which are sold in the US. Scope out the details in the press release below and click the image above to see it all laid out in a handy infographic.

Acura confirms more 2016 NSX details

Acura served up a slew of engineering details about the soon-to-launch 2016 NSX. Fittingly, they were explained at a dinner at the SAE International World Congress in Detroit, where morsels about the new Acura supercar were likely gobbled up quicker than the main course. Among the highlights: The NSX will mark Acura's first use of a multimaterial space frame, and it includes high-strength steel and aluminum. This will allow the NSX to hit its weight targets, while maintaining rigidity. The NSX uses a so-called "ablation" technology, which allows the ultra-rigid castings to be used within the car's crush zones. For more details on this, scroll through the press blast below. As expected, the NSX will pack a twin-turbo V6 engine, and Acura confirmed it will displace 3.5 liters. The unit will be mounted amidships and team with hybrid components to increase performance and efficiency. The supercar also features the most advanced evolution of Acura's Super Handling All-Wheel-Drive system, and it's capable of distributing more torque than any other setup the brand has used. The NSX has 10 air-cooled heat exchangers that will cool the powertrain, and the V6 alone will have three radiators. There are also twin intercoolers in the side air intakes that further cool the system. The next generation of the NSX was unveiled in January at the Detroit Auto Show, and production launches this fall in Ohio. Related Video: New Technical Details of the Next Generation Acura NSX Revealed at SAE 2015 World Congress and Exhibition . DETROIT, April 23, 2015 – In advance of the market launch of the highly anticipated next generation Acura NSX, the engineers leading the supercar's development shared new technical details and design strategies with the automotive engineering community at the April 22nd SAE Detroit Section dinner, held in conjunction with the SAE 2015 World Congress and Exhibition. Additional information about the team's efforts to achieve a true "New Sports Experience" included details of the NSX's world's first body construction process that helped create a multi-material space frame resulting in class-leading body rigidity, the advanced total airflow management system and an update on NSX's power unit specifications. Ted Klaus, chief engineer and global development leader of the new NSX, introduced key powertrain, body and dynamic performance engineers who shared new product and technical details in their related areas of the development.