1999 Toyota Rav4 All Wheel Drive,4cyl,4door, Auto Trans,ac, Good Condition, on 2040-cars

Auto blog

How Toyota's 100-year textile history influenced FCV hydrogen fuel cell car

Turns out, Toyota had a surprising ace in the hole when it came to building the new fuel tanks for the FCV hydrogen fuel cell car, which is coming next year. Well before Toyota became the Toyota Motor Company, it was the Toyota Industries Corporation and it made textile looms. This is important because the main structure of the hydrogen tank is wound carbon fiber. When Toyota set out to increase the strength of the tanks to hold hydrogen stored at 10,000 psi (up from 5,000 in the previous tanks), it was able to draw on its 100-year-old history as it designed its car of the future. "A lot of that textile experience came back when we did the tank wrapping." – Justin Ward "We have a lot of experience with textiles," Justin Ward told AutoblogGreen at the 21st World Congress on Intelligent Transport Systems (ITS) in Detroit this week, "and a lot of that textile experience came back when we did the tank wrapping." On top of being able to hold the higher-pressure hydrogen, Toyota's first attempt to build its own hydrogen tank was six times faster than the industry standard, so it saved time and money as well as working better. The company will also be able to inspect its own tanks. Ward is the general manager of powertrain system control at the Toyota Technical Center and hydrogen vehicles are something he knows a lot about. The reason for the stronger, 10,000-psi tanks is because the 5,000-psi tanks only offered around 180-200 miles of range, even with four tanks in the early $129,000 FCHV Highlander hydrogen prototypes. The FCV only has two, but they will able to deliver the 300-mile range that customers told Toyota they wanted. Dropping the number of tanks not only obviously reduced the cost for the tanks themselves but also the number of valves and hoses and other components you need. Despite the benefits of higher compression, going much higher doesn't make sense. 10,000 psi is the "natural progression," Ward said, because "you start to bump up against compression inefficiencies." Think of an air compressor. When hydrogen is produced at a wastewater treatment plant or a reforming site, Ward said, is it at around ambient pressure (14 psi). That has to be raised, using compressors, all the way to 10,000 psi. "That takes energy," Ward said, "and every doubling of pressure adds another doubling of energy needed, so it starts to add up pretty fast if you go too high." Component specifications are also fine at 10,00 psi, but more difficult at higher levels.

Jay Leno goes offroading with the legendary Ivan 'Ironman' Stewart

Jay Leno takes a step outside of his cavernous garage for this latest video for a jaunt into the desert to get a little dirty. He meets up with off-road racing legend Ivan 'Ironman' Stewart, who has multiple Baja 500 and 1000 wins in his motorsports career, to play with a Toyota Tundra in the sand.
Unfortunately, Leno doesn't get to interview Stewart too deeply about his long history in racing, but Ironman does talk a little bit about reading the trail while speeding through the desert. In lieu of a great conversation, there is a ton of high-quality footage of the Toyota bounding through the desert.
This clip feels more like a marketing effort than the usual output from Jay Leno's Garage, but it's still great to see Stewart behind the wheel sliding a truck, just like old times. The two of them even take the truck on a somewhat humorous journey at the end of the video.

Automakers' sound systems: Crank it, don't yank it

Years ago, one of the first things most music lovers did after buying a new vehicle was drive to an aftermarket stereo shop to get the crappy stock components swapped for better gear. And you'd typically get not only better sound but also more bang (and boom) for your buck. But in the past decade or so, the overall quality of OEM audio has dramatically increased, while car electronics became more complex, removing the incentive for most new vehicle owners — and all but the most hardcore DIYer — to start from scratch. In 2010, I did a comparison of the average costs for OEM electronics vs. similar offerings from the aftermarket, and back then automakers' stock premium systems were by far the best bargain — and are probably an even better value now. The premium 14-speaker, 1,200-watt JBL system in the all-new 2019 Toyota Avalon is a prime example of this trend. It's standard on the top two Limited and Touring trims and is available as a $680 audio upgrade on the XLE and XSE. I doubt you can even buy 14 speakers and 1,200 watts of amplification from the aftermarket for 700 bucks, much less have it all installed. And because the system is bundled with Toyota's Entune infotainment system, Apple CarPlay and a surround-view camera, removing the head unit means you would likely lose these features. Another advantage of OEMs and their audio partners is they can design the car around the audio system. In the past, automakers would typically place speakers where convenient for packaging, not for optimal sound reproduction, and audio engineers were forced to compromise. But as with the Avalon's premium JBL audio system, this is starting to change. At a recent behind-the-scenes peek for media into the process of developing the system, Toyota and Harman engineers delved into the minutia of sealing the inner panel of the front doors to create an enclosure for 6x8-inch woofers, making space in the pillars for JBL horn tweeters and extensively measuring the acoustic properties of the interior to tune the sound to the space. I'm met some creative and skilled car stereo installers, but none with a degree in psychoacoustics. The system is also the first to feature Quantum Logic Surround that creates a multi-channel listening experience from two-channel sources. And it includes Harman's Clari-Fi processing that "rebuilds key details lost" in compressed audio formats used by streaming music services and MP3s.