2001 Toyota Camry Le Sedan 4-door 81k Miles Parts Car Wrecked Rebuildable Nr!!! on 2040-cars

Auto blog

Audi investing $30.3 billion through 2018 for product expansion

How does Audi plan to reach two million units in annual sales and pay for the 11 new models it's adding to its lineup - an expansion that may include models named SQ2, Q9 and F-Tron? By increasing its investment to 22 billion euros ($30.3 billion US) between now and 2018. That figure represents an increase of about 500 million euros over the previously planned outlay, according to a report by Automotive News, and that could be due to Audi wishing to goad the momentum that pushed it to 1.5 million annual sales two years ahead of schedule.
It's also about staving off the challenges from BMW and Mercedes-Benz. Now that BMW has been able to turn some of its attention away from its "i" series of Megacity cars, it will reportedly spend more than planned in 2014 as it continues the rollout of ten all-new vehicles and 15 new-generation vehicles through the end of next year. Mercedes, having been dropped to third in the sales race, is preparing to add 13 new cars over the next six years.
Audi's money is going into technology, into product like the next-generation TT and the Q1 and production expansions and upgrades all over the world. The expenditure represents just under a fourth of Volkswagen's 84.2 billion-euro ($115.7 US) outlay devoted to taking the number-one global automaker title away from General Motors and Toyota by 2018.

How Toyota's 100-year textile history influenced FCV hydrogen fuel cell car

Turns out, Toyota had a surprising ace in the hole when it came to building the new fuel tanks for the FCV hydrogen fuel cell car, which is coming next year. Well before Toyota became the Toyota Motor Company, it was the Toyota Industries Corporation and it made textile looms. This is important because the main structure of the hydrogen tank is wound carbon fiber. When Toyota set out to increase the strength of the tanks to hold hydrogen stored at 10,000 psi (up from 5,000 in the previous tanks), it was able to draw on its 100-year-old history as it designed its car of the future. "A lot of that textile experience came back when we did the tank wrapping." – Justin Ward "We have a lot of experience with textiles," Justin Ward told AutoblogGreen at the 21st World Congress on Intelligent Transport Systems (ITS) in Detroit this week, "and a lot of that textile experience came back when we did the tank wrapping." On top of being able to hold the higher-pressure hydrogen, Toyota's first attempt to build its own hydrogen tank was six times faster than the industry standard, so it saved time and money as well as working better. The company will also be able to inspect its own tanks. Ward is the general manager of powertrain system control at the Toyota Technical Center and hydrogen vehicles are something he knows a lot about. The reason for the stronger, 10,000-psi tanks is because the 5,000-psi tanks only offered around 180-200 miles of range, even with four tanks in the early $129,000 FCHV Highlander hydrogen prototypes. The FCV only has two, but they will able to deliver the 300-mile range that customers told Toyota they wanted. Dropping the number of tanks not only obviously reduced the cost for the tanks themselves but also the number of valves and hoses and other components you need. Despite the benefits of higher compression, going much higher doesn't make sense. 10,000 psi is the "natural progression," Ward said, because "you start to bump up against compression inefficiencies." Think of an air compressor. When hydrogen is produced at a wastewater treatment plant or a reforming site, Ward said, is it at around ambient pressure (14 psi). That has to be raised, using compressors, all the way to 10,000 psi. "That takes energy," Ward said, "and every doubling of pressure adds another doubling of energy needed, so it starts to add up pretty fast if you go too high." Component specifications are also fine at 10,00 psi, but more difficult at higher levels.

How platform problems are delaying next-gen Prius

Short-term pain for longer-term gain? That may be the prognosis for the next-generation Toyota Prius, the world's best-selling hybrid. But, hey, the new version might get holiday season debut, now. Toyota is upgrading some of its most popular models and trying to cut long-term costs with components that can be used on multiple models on the new Toyota New Global Architecture platform, Automotive News says. That means more parts that can be used for the Camry, Avalon (not big stretch, since the Avalon is basically a rich man's Camry) and Corolla in addition to the Prius. The downside, of course, is that this takes a bit more engineering and certainly more time. In the case of the Prius, that means pushing back the start of production from next summer to December 2015. But Automotive News also says the Prius may have an all-wheel-drive option. Happy Holidays. The report is in update from Automotive News Europe, which cited folks familiar with the process who were not identified and said late last month that the production of the fourth-gen Prius would be pushed back by about six months as engineers continue to tweak the hybrid powertrain for maximum efficiency. The goal is around a 10 percent improvement in fuel-efficiency thanks to an upgraded powertrain and lower vehicle weight. Toyota spokeswoman Amanda Rice told AutoblogGreen in an email that the company doesn't comment on future products, so we'll just have to keep an eye out.