1999 Toyota Camry Le-4 Door Sedan-2.2 Liter-4 Cylinder-low Miles-runs Great on 2040-cars

Auto blog

Toyota sells six of 10 of hybrids in California

In an apparent shot back at Ford's increasing market share of electrified vehicles and claim that it accepts more Prius trade-ins for its own hybrids than any other car, Toyota has flexed a muscle and played the numbers game to put the Blue Oval in its place.
Leaning on its hybrid market dominance in California, the Japanese automaker stated that six out of 10 hybrids sold in the Golden State are Toyota models. And it keeps coming: Year-to-date through May 2013, Toyota sold five times more hybrids than Ford. One of every two hybrids in California is a Prius model. In addition, Toyota notes that it has sold 1.5 million Prius vehicles in the US, 90-percent of which are still on the road today.
Want more? We'll let Bill Fay, Toyota's group vice president and general manager of sales lay the smack down:

Toyota to recall 185k cars globally, including Yaris

Toyota has announced it is recalling a total of 185,000 vehicles worldwide for a power steering issue. Yaris and (overseas) Vitz models built between November 2010 and March 2012 could suffer a short circuit in their power steering control module if water gets inside. Should that happen, the power steering could fail, increasing effort when turning. The recall also includes the Verso-S and Ractis built from August 2010 to August 2011. The recall covers 130,000 vehicles in Japan and around 22,450 in Europe.
Only 74 units are being recalled in the United States.
Toyota says if the fault occurs, the vehicle will display the Electronic Power Steering warning light on the dash and a buzzer will sound. The automaker will alert owners by mail and dealers will replace the power steering control module free of charge. You can read the quick press release on the recall below for more information.

How Toyota's 100-year textile history influenced FCV hydrogen fuel cell car

Turns out, Toyota had a surprising ace in the hole when it came to building the new fuel tanks for the FCV hydrogen fuel cell car, which is coming next year. Well before Toyota became the Toyota Motor Company, it was the Toyota Industries Corporation and it made textile looms. This is important because the main structure of the hydrogen tank is wound carbon fiber. When Toyota set out to increase the strength of the tanks to hold hydrogen stored at 10,000 psi (up from 5,000 in the previous tanks), it was able to draw on its 100-year-old history as it designed its car of the future. "A lot of that textile experience came back when we did the tank wrapping." – Justin Ward "We have a lot of experience with textiles," Justin Ward told AutoblogGreen at the 21st World Congress on Intelligent Transport Systems (ITS) in Detroit this week, "and a lot of that textile experience came back when we did the tank wrapping." On top of being able to hold the higher-pressure hydrogen, Toyota's first attempt to build its own hydrogen tank was six times faster than the industry standard, so it saved time and money as well as working better. The company will also be able to inspect its own tanks. Ward is the general manager of powertrain system control at the Toyota Technical Center and hydrogen vehicles are something he knows a lot about. The reason for the stronger, 10,000-psi tanks is because the 5,000-psi tanks only offered around 180-200 miles of range, even with four tanks in the early $129,000 FCHV Highlander hydrogen prototypes. The FCV only has two, but they will able to deliver the 300-mile range that customers told Toyota they wanted. Dropping the number of tanks not only obviously reduced the cost for the tanks themselves but also the number of valves and hoses and other components you need. Despite the benefits of higher compression, going much higher doesn't make sense. 10,000 psi is the "natural progression," Ward said, because "you start to bump up against compression inefficiencies." Think of an air compressor. When hydrogen is produced at a wastewater treatment plant or a reforming site, Ward said, is it at around ambient pressure (14 psi). That has to be raised, using compressors, all the way to 10,000 psi. "That takes energy," Ward said, "and every doubling of pressure adds another doubling of energy needed, so it starts to add up pretty fast if you go too high." Component specifications are also fine at 10,00 psi, but more difficult at higher levels.