2014 Toyota Avalon Xle Touring on 2040-cars

Auto blog

Toyota, Lexus dominate KBB's Best Resale Value Awards

Toyota and Lexus stormed the 2014 Kelley Blue Book Best Resale Value Awards, winning a combined 18 categories including best brand and best luxury brand. This marks the third year in a row that both automakers have won the Brand and Luxury Brand resale value awards. In all, Toyota won 11 categories and Lexus won seven.
Honda made a good showing, as well, winning two segments (Accord Plug-In Hybrid and Civic Si) and putting one car on the top-10 Best Resale Value list (CR-V). Chevrolet did even better, winning two segments (with the V6 Camaro and the Corvette) and placing three cars on the top-10-overall list (again, the Camaro and Corvette, plus the Silverado 1500).
The other winners came from Jeep, Dodge, Infiniti, Subaru and Audi. To give you a clearer picture of the Toyota and Lexus domination, their 18 mentions represents more than half of the 34 awards (including the top-10-overall list).

Toyota recalls 337,000 RAV4s and HS250h models for tie rod failure

UPDATE: The post has been updated with additional information from NHTSA. The Basics: Toyota is recalling 337,000 2006-2011 model year Toyota RAV4 crossovers built between October 31, 2005 and September 7, 2010 as well as 2010 model year Lexus HS250h cars built between July 6, 2009 and August 26, 2010. The Problem: When either an affected RAV4 or HS250h is given an alignment and the tie rod adjustment nut on the rear control arm isn't tightened properly, the threads on the tie rod can start to rust. If this happens, the nut may break off and throw off the alignment drastically and suddenly. This isn't a case of the car simply pulling to one side, either. This would seriously upset the balance of the car and could cause the driver to lose control and crash. This is also the third time these vehicles have been recalled for the same issue. Injuries/Deaths: It's unknown if this control arm issue has resulted in any injuries or deaths. Autoblog reached out to Toyota for more information, but a company representative told us that the company isn't able to discuss injuries or deaths caused by this issue (if any) at this time. Based on information from NHTSA documents, it does not appear that any crashes, injuries or deaths have been attributed to the defect addressed in the current recall. The Fix: The dealer will completely replace the rear suspension assemblies at no cost to the owner. The tie rods and nuts will also be coated in epoxy to prevent future rusting from occurring. According to Car and Driver, the previous recalls involved tightening nuts, coating decent tie rods in epoxy and completely replacing rusted ones. The car magazine reports that further complaints were filed and the company is now replacing all components regardless of condition. If you own one: Toyota will notify owners of affected cars by mail. Owners can also check whether their cars are affected by entering the VIN at safercar.gov/vin. Owners with questions can also reach Toyota customer service at 1-800-331-4331 or Lexus customer service at 1-800-255-3987. Related Video: Featured Gallery 2012 Toyota RAV4 View 16 Photos News Source: Car and Driver, Toyota, National Highway Traffic Safety AdministrationImage Credit: Toyota Recalls Lexus Toyota Safety lexus hs 250h lexus hs250h

How Toyota's 100-year textile history influenced FCV hydrogen fuel cell car

Turns out, Toyota had a surprising ace in the hole when it came to building the new fuel tanks for the FCV hydrogen fuel cell car, which is coming next year. Well before Toyota became the Toyota Motor Company, it was the Toyota Industries Corporation and it made textile looms. This is important because the main structure of the hydrogen tank is wound carbon fiber. When Toyota set out to increase the strength of the tanks to hold hydrogen stored at 10,000 psi (up from 5,000 in the previous tanks), it was able to draw on its 100-year-old history as it designed its car of the future. "A lot of that textile experience came back when we did the tank wrapping." – Justin Ward "We have a lot of experience with textiles," Justin Ward told AutoblogGreen at the 21st World Congress on Intelligent Transport Systems (ITS) in Detroit this week, "and a lot of that textile experience came back when we did the tank wrapping." On top of being able to hold the higher-pressure hydrogen, Toyota's first attempt to build its own hydrogen tank was six times faster than the industry standard, so it saved time and money as well as working better. The company will also be able to inspect its own tanks. Ward is the general manager of powertrain system control at the Toyota Technical Center and hydrogen vehicles are something he knows a lot about. The reason for the stronger, 10,000-psi tanks is because the 5,000-psi tanks only offered around 180-200 miles of range, even with four tanks in the early $129,000 FCHV Highlander hydrogen prototypes. The FCV only has two, but they will able to deliver the 300-mile range that customers told Toyota they wanted. Dropping the number of tanks not only obviously reduced the cost for the tanks themselves but also the number of valves and hoses and other components you need. Despite the benefits of higher compression, going much higher doesn't make sense. 10,000 psi is the "natural progression," Ward said, because "you start to bump up against compression inefficiencies." Think of an air compressor. When hydrogen is produced at a wastewater treatment plant or a reforming site, Ward said, is it at around ambient pressure (14 psi). That has to be raised, using compressors, all the way to 10,000 psi. "That takes energy," Ward said, "and every doubling of pressure adds another doubling of energy needed, so it starts to add up pretty fast if you go too high." Component specifications are also fine at 10,00 psi, but more difficult at higher levels.