4dr Automatic 2.5x Limited Low Miles Suv Automatic Gasoline 2.5l 4 Cyl Engine Wh on 2040-cars

Auto blog

Subaru teasing STI surprise for NYC show?

Subaru is no stranger to the Special Edition car, least of all where its vaunted WRX and STI are concerned. From Spec C to Prodrive to 22B, more than a handful of STI's around the world have been released as limited-run editions, often with stirring results. So, while we were more than a little bit surprised to see that big-wing crop up on the Subaru Twitter page today, we can't say as though its not true to the brand's history.
However, while most of the interesting WRX STI variants have been offered to Europe and Japan only, whatever is wearing that carbon-fiber-lipped wing is set to debut at the New York Auto Show this week.
We don't have a clue as to the precise nature of the car in front of that wing, save to say that it's likely based on the STI. We can guess, however that the extra vertical supports and the use of carbon fiber indicate a higher-performance version than currently exists. Anything from a racing application to some new goodies for the aftermarket are in the realm of possibility.

2016 Subaru Outback, Legacy recalled for driveshaft problem

The Basics: Subaru is recalling 3,251 examples of the 2016 Legacy built between Oct. 24, 2015, and Nov. 16 2015, and the 2016 Outback manufactured between Oct. 24, 2015, and Nov. 17, 2015. The Problem: The driveshaft could separate from the rear differential because the securing nuts aren't tight enough. If this happens, the driveshaft could hit the gas tank, leading to a fuel leak. Injuries/Deaths: Subaru spokesperson Michael McHale confirms to Autoblog there are no reports of accidents, injuries, or fires. The fix: Subaru dealers will inspect the nuts and tighten or replace them as necessary. If you own one: Subaru expected the recall to begin on December 10, so owners should receive notification very soon. Related Video: RECALL Subject : Drive Shaft May Detach From Differential Report Receipt Date: NOV 24, 2015 NHTSA Campaign Number: 15V794000 Component(s): POWER TRAIN Potential Number of Units Affected: 3,251 All Products Associated with this Recall Vehicle Make Model Model Year(s) SUBARU LEGACY 2016 SUBARU OUTBACK 2016 Details Manufacturer: Subaru of America, Inc. SUMMARY: Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential. CONSEQUENCE: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire. REMEDY: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57. NOTES: Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

UK designer to make WRX Concept-aping body kit for production Subaru

Remember the Subaru WRX Concept shown at the 2013 New York Auto Show, the one almost everyone loved but no one expected Subaru to make? Indeed, that Parnassian "design statement" led to a production design that came from a good middle class neighborhood known for its office parks and pasture land. UK designer Michael Bond is offering to change that, the man behind the yet-to-be-produced Rumbler "Superhero Utility Vehicle" touting the Subaru WRX Concept 13, which would take a customer's new WRX and turn it into something pretty close to the original concept.
That means new front and rear clips, including a redesigned rear diffuser to increase downforce, but a spoiler can be installed if the buyer decides that what he wants. The car won't be an exact replica of the NYIAS concept since that would infringe on Subaru's intellectual property, but it isn't clear yet how the design would be altered. Bond's site says that once he gets 50 confirmed orders, his team will order a WRX and begin the process of creating the new bodywork. It is claimed that once work begins, it will be four to six months to "[present] a completed model for public view."
Bond says the price will come down depending on the number of orders beyond 50, but doesn't give any indication of how much those first 50 cars could cost. If you're keen, though, head over to the site and fill out the enquiry form. Who knows if the Concept 13 will happen, but so far this is the best chance you have of getting what could have been.