2013 Ram 1500, Single Cab, 5100 Miles, 5.7 Hemi V8, 20 Inch Wheels, Xm Radio on 2040-cars

Auto blog

FCA recalls 2 million Ram trucks over airbag issues

Airbag issues have prompted Fiat Chrysler Automobiles to issue another pair of recalls. The two separate issues both affect Ram pickups, one campaign stemming from oversensitive sensors, the other from a wiring harness. Between them, the problems affect an estimated combined total of some 2 million units. The first recall affects 2013-15 Ram 1500, 2500, and 3500 trucks, specifically four-door models, manufactured between June 20, 2012, and January 26, 2015. The calibration of the side impact sensor in those affected units may to be too sensitive. As a result, if the door is slammed too hard, the side-curtain airbag and seatbelt pre-tensioner may inadvertently activate. FCA reports that this issue affects an estimated 667,406 units in the United States, plus 153,011 in Canada, a further 8,272 in Mexico, and another 14,847 in markets outside of North America, amounting (in Chrysler's estimation) to less than 0.005 percent of those vehicles produced. The automaker says it is aware of two minor injuries (but no accidents) that may have resulted from the glitch, and is taking action to have the Occupant Restraint Control module recalibrated in the affected units. The second issue also affects Ram pickups, including 1500, 2500, 3500, 4500, and 5500-series models from the 2012 to 2014 model years, built between January 18, 2011, and October 7, 2014, and fitted with the optional Electronic Vehicle Information Center. The problem here stems from a wiring harness in the steering wheel that may rub against a retainer spring in the air bag control module, which in turn could cause an electrical short and deploy the driver's side air bag unexpectedly. In the United States alone, the issue is estimated to affect 1,060,531 units, which will need to be inspected and, where necessary, have their steering wheel wiring harnesses secured, with protective caps added to the ends of the airbag retainer spring. These do not represent the first issues we've seen from Fiat Chrysler in recent days. The automaker recently issued a recall for approximately 1.4 million vehicles to have their Uconnect software updated to prevent hacking. A few days ago it also announced a recall for 350,000 Dodge Journey (and Fiat Freemont) crossovers to secure loose engine covers. And the National Highway Traffic Safety Administration is expected to issue Fiat Chrysler Automobiles a $105-million fine for mishandling other recent recalls and safety issues.

Ram flubs ProMaster cargo capacity

The Ram ProMaster is going to look a little smaller on the inside, at least by way of its specification sheets, despite the sheet metal staying the same.
When Ram originally published the cargo capacity for its van, it simply did a direct conversion from the European rating of 15 cubic meters to 530 cubic feet. However, that didn't take into account the standard way internal measurements are calculated for the US. While the trucks have been on sale since October, the automaker just noticed the problem, and it's working on a revised figure. According to Automotive News, the new carrying ability for the ProMaster is likely between 450 and 475 cubic feet.
The difference stems from two standards for measuring capacity. In Europe, the entire internal area is determined and then obstacles like seats are subtracted from it. That means areas where freight could never go, like on top of seat backs, gets included in the figure. In the US, only the area where goods could actually fit is included, which leads to lower specs with no actual change in space.

Ram granted patent for in-bed ramp system

Most of the patent filings we report on these days are of a pretty high-tech nature: everything from "humanized" navigation systems to 11-speed transmissions. But cool innovations can be lower-tech and clever, too. At least that's our feeling after seeing some proposed plans from Ram. FCA has filed a patent for a system of built-in ramps recessed inside of a truck bed. While stowable ramps aren't new – Ford offers a similar system for the F-150 ­– the level of integration shown in these diagrams seems to be. Drawings show ramps that run on channels in the bed and tailgate, hinged at the end of the extended gate for a gentle upslope into the cargo area. What's more, the system seems changeable, with two ramps set wide or narrow, or just one centrally mounted. Just the thing for switching from motorcycle-loading season to snowmobile-loading season. A granted patent doesn't always lead to a product brought to market, of course. Issues with cost, durability, and demand all have a lot to say about what makes it from design to showroom. Still, we think the proposed RamRamp (feel free to use that, FCA) shows a ton of promise. Speak up truck owners, is a factory-installed ramp system like the one you see here something you'd pay for on your next vehicle? Get into Comments, below, and let us know. Related Video: Featured Gallery Ram in-bed ramps patent drawings News Source: USPTO via Allpar RAM Truck patent