2012 Ram 1500 Bighorn on 2040-cars

Auto blog

Mopar Muscle is Monster Jam's first OEM monster truck in over a decade

New monster trucks seem to join the Monster Jam circuit every year, but it's not often that one gets the official blessing of an automaker. That's about to change, however, as Chrysler's truck division has teamed up once again with Hall Brothers Racing - which already fields the championship-winning Raminator and Rammunition trucks - to field the series' first new Original Equipment Manufacturer monster truck in over a decade.
Dubbed Mopar Muscle, the new Ram monster truck will debut at the Monster Jam in Detroit on Saturday at Ford Field, at the first of six such events in which Mike Miller (who, incidentally, named his son Hemi) will drive the truck throughout the year.
Here's what you need to know: Based on a 2014 Ram HD pickup (or at least made to look like one), Mopar Muscle stands 10 feet tall and weighs over 10,000 pounds, and it's powered by the legendary Gen II 426 Hemi that celebrates its 50th anniversary this year. But instead of leaving the massive 7.0-liter engine as is, Hall Brothers Racing enlarged it to 565 cubic inches - a mind-boggling 9.3 liters - and supercharged it to 2,000 horsepower. That's a whole lot of muscle no matter what it's packed into. Check it out in our high-res image gallery above. You can also check out the full schedule of events in the press release below to see if the truck is coming to your area this year.

A beginner's guide to plowing snow with a heavy-duty truck

I live in a desert, so the only things getting plowed around here are mud flows and brewer neighbors. But I enjoy machinery and haven't plowed any snow since a "loaded" truck meant one with A/C and a CD player, so I jumped at the chance for a plow primer in a Ram HD on a Canadian airfield. Running a plow is like welding – the basics come quickly but experience pays dividends. The first thing to deal with is a frequently changing horizon because, stout as they are, even three-quarter-ton heavy-duty trucks will move up and down in front considerably with a 600-to-800-pound plow hanging off, and fast plow hydraulics rival some low-riders for bounce effect. Getting going is easy unless you forgot blocks and the plow froze to the ground, rookie. If you have to drive to your plowing assignment, blade height needs some experimentation to find the best cooling airflow; if you think sub-freezing temperatures negate that concern, remember you've installed what amounts to a 20-square-foot air brake up front that the truck has to overcome, and blowing snow could block some cooling air passages. Whether it's a "straight" blade or V design, always have it tilted to the right lest you catch a hidden post, solid mailbox, or edge of a snow bank. Most plow operators I spoke to rarely exceed 45 mph in transit because of cooling, front suspension travel, and common sense, and you should go even slower if you don't have some ballast like chains, extra fuel tanks, or a salt spreader to balance the load on the back. With trucks' relatively slow steering and all that weight up high, oversteer is best avoided. With a little clean space to get a run, stick it in Drive to gather momentum and lower the plow simultaneously to float, where the weight of the plow rests on and lets it run along the surface. Momentum is good until you hit something you didn't know about, at which point the plow's breakaway systems limit damage but your truck could still hit something big; caution never hurts. Start out at 10 to 15 mph, depending on consistency and depth, making a clean wave off one side. If you have to push it straight, as you slow coincidentally raise the blade at the bottom of the pile to shove it up higher. Carry too much speed here and you'll stop with an unceremonious thud. Common mistakes cited among a few experts were people pushing banks of snow rather than plowing it, and rushing the shift between Drive and Reverse, throttling up before the shift is completed.

FCA plants skipping summer shutdown to keep up with demand

Hopefully, some FCA US factory employees don't have big plans for the usual summer shutdown, because the automaker is keeping several plants running this year. Demand is so high that the company wants to keep models rolling off the assembly lines. Four FCA US assembly plants, all the engine factories, and some locations that build transmissions are staying open throughout the summer, according to the Detroit Free Press. Usually, these sites would see a two-week shutdown for the company to retool and perform repairs. This year, factories are staying open for FCA to support its strong sales. The lines that remaining humming through the summer show an inclination toward the automaker's popular SUV's and crossovers. They include the Jefferson North Assembly Plant in Michigan that builds the Jeep Grand Cherokee and Dodge Durango; Saltillo Van Assembly in Mexico that constructs the Ram ProMaster; Toledo Assembly Complex in Ohio that produces the Cherokee and Wrangler; and Toluca Assembly in Mexico that makes the Dodge Journey and Fiat 500. Related Video: News Source: The Detroit Free PressImage Credit: Bill Pugliano / Getty Images Plants/Manufacturing Dodge Fiat Jeep RAM FCA dodge journey fca us ram promaster Jefferson North Assembly Plant