on 2040-cars

Auto blog

How to update and secure a vulnerable Chrysler Uconnect system

If you own one of the 1.4 million vehicles affected by the recent Chrysler software recall, you may want to watch this video. In it, we explain how to get the latest infotainment software loaded onto the 8.4-inch Uconnect system. The recall was a response to the findings of researchers who were able to hack into and remotely control a 2014 Jeep Cherokee through its cellular connection. Although Fiat Chrysler has worked with Sprint to plug most of the holes on the carrier side, there are still some vulnerabilities that only this latest software version can patch. Owners have three options to get the update: download it now, wait for a USB stick in the mail, or take the vehicle to an FCA dealer. Chrysler will be sending USB sticks loaded with the software update to customers. Anyone with an internet connection and a USB stick of their own with at least 4 GB capacity can speed things up by downloading the patch from the Uconnect website. We cover that process from start to finish in the video, with the final portion still applicable to those using the FCA-supplied USB stick. If after watching this you still don't want to tackle the patch yourself, you can take your vehicle to the dealer to have it done. Also note that this process is the same for all Uconnect updates, not just the one patching the exploits. Our demonstrator vehicle is a 2015 Ram 1500 pickup. The procedure should be very similar on other products with the 8.4-inch Uconnect system, with only the location of the USB port varying. Once you have the USB stick with the software on it – either after having downloaded it yourself or receiving it in the mail from Chrysler – the installation process is relatively simple. It takes about 15 minutes to perform the update; we edited out the wait in the video. To check whether or not your car's 8.4-inch Uconnect system is running the latest software, go to System Information on the touch screen's Settings page and look at Software Version. The update related to the recall is version 15.17.5. Related Video: Recalls Chrysler Dodge Jeep RAM Safety Technology Infotainment Videos Original Video hacking

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.

FCA looking into Ram-based SUV, midsize pickup

Fiat Chrysler Automobiles (FCA) is looking into manufacturing a large SUV based on the Ram 1500 pickup truck's current platform, reports USA Today. If built, the SUV would compete against the Chevrolet Tahoe and could even spawn a smaller pickup. Ram already has most of the bases covered with its current lineup, but a smaller pickup truck would allow it to enter the booming midsize pickup segment where it would compete with the segment-leading Toyota Tacoma along with the Chevy Colorado and GMC, which are the newest entries. Mike Manley, head of Fiat Chrysler's Jeep and Ram brands, told USA Today that the current platform found in the Ram 1500 could be utilized for a body-on-frame SUV. With a large SUV, FCA would be able to capitalize on the ever-growing SUV market and go toe-to-toe with General Motors (GM) and Ford. The next-generation of Ram pickup trucks is expected to go on sale in early 2018, which would put a large SUV close behind. In an attempt to increase the automaker's production capacity, FCA also plans to move Ram's current production facility from Warren to Sterling Heights, MI. With Jeep continually posting healthy numbers, it makes perfect sense for FCA to build more SUVs. GM currently uses the same platform on a plethora of its SUVs with good results, which makes FCA's proposed plan a viable option. Related Video: News Source: USA Today, Scott Olson/Getty RAM Truck SUV