1999 Pontiac Sunfire 4dr 112k Great Mpg on 2040-cars

Auto blog

Junkyard Gem: 1984 Pontiac Fiero with supercharged 3800 V6 swap

Like the Corvair, the Vega, and the Citation, the Pontiac Fiero was a very innovative machine that ended up causing General Motors more headaches than happiness, and Fiero aficionados and naysayers continue to beat each other with tire irons (figuratively speaking, I hope) to this day. The General has often proved willing to take the occasional big gamble and huge GM successes in engineering prowess (including the first overhead-valve V8 engine for the masses and the first real-world-usable true automatic transmission) and marketing brilliance (e.g., the Pontiac GTO and related John DeLorean home runs) meant that the idea of a mid-engined sporty economy car (or economical sports car) got a shot from the suits on the 14th floor. Sadly, the Fiero ended up being the marketplace victim of too many issues to get into here, and The General pulled the plug immediately after the 1988-model-year suspension redesign that made the Fiero the sports car it should have been all along. But what if the plastic Pontiac had never suffered from the misery of the gnashy, pokey Iron Duke engine and had been built from the start with a screaming supercharged V6 making way better than 200 horsepower? The final owner of today's Junkyard Gem sought to make that very Fiero, by dropping in one of the many supercharged 3.8-liter V6s installed in 1990s and 2000s GM factory hot rods. The first Fieros came out in 1983 for model year 1984, and the only engine available that year was the Iron Duke 2.5-liter four-cylinder, which generated its 92 horsepower with the full-throated song of a Soviet tractor stuck in the freezing mud of a Polish sugar-beet field. The 2M4 badging stood for "two seats, mid-engine, four cylinders," just as the numbers in the Oldsmobile 4-4-2 once represented "four carburetor barrels, four-speed manual transmission, dual exhaust." This car is a top-trim-level SE model, which listed for $9,599 (about $24,200 today). The no-frills Fiero cost just $7,999 that year, making these cars far cheaper than the only other reasonably affordable new mid-engined car Americans could buy at that time: the $13,990 Bertone (aka Fiat) X1/9. The Toyota MR2 appeared in North America as a 1985 model with a base price of $10,999 and promptly siphoned off the car-buying cash from a bunch of potential Fiero shoppers.

General Motors Recall List

It seems General Motors can't go more than a few weeks without issuing a major recall. Since the initial ignition lock recall on February 10, over 25 million vehicles have been recalled for defects. It seems General Motors can't go more than a few weeks without issuing a major recall. Since the initial ignition lock recall on February 10, over 25 million vehicles have been recalled for defects. We used the National Highway Traffic Safety Administration recall list to compile a snapshot of all the GM vehicles recalled in the last two months. NHTSA also provides a search engine that allows owners to search for recalls on their vehicle. An automotive company must do everything in their power to notify its customers when a recall is issued on a vehicle. If you own any of the following vehicles and you have questions regarding your car, you can contact Chevrolet at 1-866-694-6546, GMC at 1-866-996-9463, Buick at 1-800-521-7300 and Cadillac at 1-866-982-2339. Or check out General Motor's recall site. Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153) or go to www.safercar.gov. Here's a brief summery of the other vehicles currently under recall: July 26 – 414,333 cars affected NHTSA Campaign Number: 14V447000 Models under recall: Certain model year 2011-2012 Buick LaCrosse, Regal and Chevrolet Camaro, as well as certain 2010-2012 Cadillac SRX, Chevrolet Equinox and GMC Terrain vehicles, equipped with power height adjustable driver and passenger seats. Problem: In the affected vehicles, the bolt that secures the driver's and passenger's power front seat height adjuster may fall out causing the seat to drop suddenly to the lowest vertical position. Consequence: If the driver's seat unexpectedly drops, the distraction and altered seat position may affect the drivers' control of the vehicle, increasing the risk of a crash. Solution: Dealers will replace the height adjuster shoulder bolts, free of charge. July 14 – 16,939 cars affected NHTSA Campaign Number: 14V341000 Models under recall: Certain model year 2011 Cadillac CTS vehicles manufactured October 18, 2010, to June 2, 2011. Problem: In the affected vehicles, vibrations from the drive shaft may cause the vehicle's roll over sensor to command the roof rail air bags to deploy. Consequence: If the roof rail air bags deploy unexpectedly, there is an increased risk of crash and injury to the occupants.

Gordon Murray, F1-driven production and .. the Pontiac Fiero

Gordon Murray's design and engineering chops are unquestionable. But does his carmaking approach owe something to the short-lived Pontiac Fiero, a scrappy little car program that emerged from GM against serious resistance? Murray had a Formula One career that ran from 1969 to 1991, with stints at Brabham ('69 to '86) and McLaren ('87-'91), that resulted in several shelves' worth of trophies for the cars he was instrumental in designing. He moved on to McLaren Cars, the consumer side of things, where, during his tenure from 1991 to 2004, he helped design the McLaren F1 and the Mercedes-Benz SLR McLaren, two cars that took learnings from his two decades in Formula One. What do all of these cars have in common? Three things: They are light. They were built in limited numbers. And they were (and are) exceedingly expensive—when the McLaren F1 debuted in 1994, it stickered at $815,000. Murray went on to establish Gordon Murray Design in 2007. GMD has created some interesting concept vehicles, such as the diminutive T.25 city car (94.5 inches long, 51.1 inches wide and 55.1 inches high), and the OX, a lightweight truck for the developing world that packs like an IKEA shelf and is working toward realization through a worthy crowdfunding campaign established by the Global Vehicle Trust. Now he has created a vehicle manufacturing company, Gordon Murray Automotive, that will use manufacturing methods that he developed under the moniker "iStream." Unlike a unibody, there are the "iFrame," a cage-like construction made with metallic components, and the "iPanels," which are composite. The panels aren't simply a decorative skin; they actually provide structure to the vehicle. Presumably this has something of the F1 monocoque about it. Going back to the three elements, (1) this arrangement results in a vehicle that can be comparatively light; (2) Murray has indicated that his manufacturing company will be doing limited-run production; and (3) to launch Gordon Murray Automotive they are going to be building a flagship model, about which Murray said, "With our first new car, we will demonstrate a return to the design and engineering principles that have made the McLaren F1 such an icon." Which seems to imply that it will be on the pricey side. According to the company's verbiage, "iStream forges an entirely new production method that defies conventionality with its Formula One-derived construction and materials technologies." It also sounds a whole lot like ...