2008 Pontiac Solstice Convertible 5 Speed Manual Leather Sat Cd Pwr New Tires 08 on 2040-cars

Auto blog

GM recalls 61k more vehicles in three campaigns

Following a stop-delivery order for its new midsize trucks and a rash of recent recalls, General Motors is issuing three more campaigns covering 60,575 vehicles in North America with 57,182 of them in the US. As of October 1, the automaker has issued a total of 74 recalls (see the ridiculously long chart to the right) this year covering 26,495,070 units in the US.
The largest campaign covers 46,873 examples in the US of the 2008-2009 Pontiac G8 and 2011-2013 Chevrolet Caprice Police Patrol Vehicle imported from Australia. It's possible for the driver's knee to hit the key and make it move from the "Run" to "ACC" position while driving. GM says its Holden division is developing a fixed-blade key that's supposed to fix the problem by only allowing it to rotate toward the "On" position. There has been one crash caused by this fault but no injuries or fatalities.
The second recall is for 10,005 units of the 2004-2007 Cadillac CTS-V and 2006-2007 Cadillac STS-V because "the fuel pump module electrical terminal may overheat." This can cause a flange to melt and allow the pump to leak fuel. GM specifies that the remedy for the CTS-V is replacing the fuel module and fuel tank jumper harness, but it doesn't specify how the STS-V is being repaired.

Junkyard Gem: 1968 Pontiac Catalina sedan

During the late 1960s, General Motors ruled the American car landscape, growing so dominant that the federal government considered antitrust action to break up the company. The General offered sporty Corvettes and muscular GTOs and rugged pickups and opulent Fleetwoods, sure, but the fat part of the sales numbers came from the bread-and-butter full-sized sedans and coupes, which boasted superior engineering and modern-looking styling; in 1967 alone, the Chevrolet Division moved 972,600 full-sized cars, and that's not even counting the 155,100 full-sized Chevy station wagons that year. Pontiac, Buick and Oldsmobile sold the same big cars with division-specific engines and bodywork, and they flew off the showroom floors. For 1968, the entry-level full-sized car from Pontiac was the Catalina, and I've found an example of the most affordable version of the most affordable big Pontiac for 1968, discarded in a northeastern Colorado wrecking yard about 50 miles south of Cheyenne, Wyoming. A '68 GM full-sized coupe, convertible, or even a four-door hardtop might be worth the cost and effort of a restoration, but a no-options base-trim-level post sedan with rust and plenty of body filler just won't get many takers these days. Like so many vehicles that sit outside for decades on the High Plains, this one is full of rodent nests. I wouldn't want to work on the interior of this car without a respirator and a lot of work with a shop-vac, because hantavirus is a significant danger in these parts. Alfred Sloan's plan to offer a stepladder of prestige for GM buyers, in which your first new car was a Chevrolet and you moved up through Pontiac, Oldsmobile, and Buick until you became sufficiently prosperous for Cadillac ownership, worked brilliantly for decades. In 1968, the Catalina was a notch above its Impala sibling on the Snob-O-Meter, with the sedan starting at $3,004 (about $22,600 in 2019 dollars). In fact, the V8-equipped 1968 Chevrolet Impala sedan listed at $3,033, and the Oldsmobile Delmont 88 went for $3,146, so the lines were beginning to blur between the relative positions of the lower-end GM divisions by this time. The base engine in the 1968 Catalina was a 400-cubic-inch (6.5 liter) V8 rated at 265 horsepower and enough torque to tow an aircraft carrier.

Gordon Murray, F1-driven production and .. the Pontiac Fiero

Gordon Murray's design and engineering chops are unquestionable. But does his carmaking approach owe something to the short-lived Pontiac Fiero, a scrappy little car program that emerged from GM against serious resistance? Murray had a Formula One career that ran from 1969 to 1991, with stints at Brabham ('69 to '86) and McLaren ('87-'91), that resulted in several shelves' worth of trophies for the cars he was instrumental in designing. He moved on to McLaren Cars, the consumer side of things, where, during his tenure from 1991 to 2004, he helped design the McLaren F1 and the Mercedes-Benz SLR McLaren, two cars that took learnings from his two decades in Formula One. What do all of these cars have in common? Three things: They are light. They were built in limited numbers. And they were (and are) exceedingly expensive—when the McLaren F1 debuted in 1994, it stickered at $815,000. Murray went on to establish Gordon Murray Design in 2007. GMD has created some interesting concept vehicles, such as the diminutive T.25 city car (94.5 inches long, 51.1 inches wide and 55.1 inches high), and the OX, a lightweight truck for the developing world that packs like an IKEA shelf and is working toward realization through a worthy crowdfunding campaign established by the Global Vehicle Trust. Now he has created a vehicle manufacturing company, Gordon Murray Automotive, that will use manufacturing methods that he developed under the moniker "iStream." Unlike a unibody, there are the "iFrame," a cage-like construction made with metallic components, and the "iPanels," which are composite. The panels aren't simply a decorative skin; they actually provide structure to the vehicle. Presumably this has something of the F1 monocoque about it. Going back to the three elements, (1) this arrangement results in a vehicle that can be comparatively light; (2) Murray has indicated that his manufacturing company will be doing limited-run production; and (3) to launch Gordon Murray Automotive they are going to be building a flagship model, about which Murray said, "With our first new car, we will demonstrate a return to the design and engineering principles that have made the McLaren F1 such an icon." Which seems to imply that it will be on the pricey side. According to the company's verbiage, "iStream forges an entirely new production method that defies conventionality with its Formula One-derived construction and materials technologies." It also sounds a whole lot like ...