2004 Pontiac Gto! Manual W/ Leather, Pioneer Sound & Kenwood Sub. Low Miles-61k! on 2040-cars

Auto blog

Camaro-based Trans Am SE Bandit Edition borrows Burt Reynolds

For some reason, modifying modern Chevrolet Camaros into the lurching, reincarnated shells of the Pontiac brand is still a thing. If you're the perverse sort that likes this kind of thing, you should check out the latest product from the Trans Am Depot, which comes complete with an endorsement from the star of Smokey and the Bandit, Burt Reynolds. Yes, the new Trans Am SE Bandit Edition has been signed and endorsed by the man himself, but what's important here is not the signature on the dash, it's the bits of Camaro that have been modified. Aesthetically, that means a Bandit-and-Frog-approved set of T-tops, a front-opening hood with a very large, prominent shaker scoop, an equally large and prominent screaming chicken, and Trans Am-inspired front and rear fascias. And naturally, Burt Reynolds' signature adorns the dash. There are plenty of reminders in the cabin about this car's Hollywood inspiration, too. Bandit decals can be found on the front headrests and center console lid, there are chicken wings on the Camaro-spec plastic door inserts, and the black-and-tan color scheme matches nicely with the exterior look. And power? Well, Sheriff Buford T. Justice would have a lot more trouble keeping up with this Trans Am than he did with the original. The 7.4-liter LSX V8 has been paired with a 2.9-liter supercharger which is good for 840 horsepower. It's fast and loud, and even if you can't get behind the look (we can't), at least this Camaro-in-Trans Am's clothing can impress with its performance. The Bandit Edition is limited to just 77 units with prices starting around $115,000. You can check out the official video from Trans Am Depot, which comes with a decent helping of Burt Reynolds, up top. Related Video:

'67 Chevy Corvair convertible vs. '86 Pontiac Fiero in cult classic showdown

Every few a decades, the folks running General Motors lose their minds briefly try to market a car that public doesn't see coming and often aren't ready for. In the '60s there was the rear-engine, air-cooled Chevrolet Corvair, then the mid-engine Pontiac Fiero in the '80s and the completely bizarre Chevy SSR in the 2000s. What all of these had in common was that they bucked the trend for American models of their era, for better or worse. The latest episode of Generation Gap tasked the hosts with finding two cult classic vehicles to choose between; they came come up with two of these quirky products from The General.
On the classic side, there's a 1967 Chevy Corvair Monza convertible. Being from later in the production run, it wears slightly more aerodynamic styling than the earlier, boxier examples. Hanging out back is an air-cooled, 2.7-liter flat-six pumping out a robust 95 horsepower. In the other corner is the somewhat more modern 1986 Pontiac Fiero SE with a mid-mounted, 2.5-liter "Iron Duke" four-cylinder, an engine nearly ubiquitous in GM cars of the '80s.
Judging by when they were new, the Corvair was far more successful than the Fiero with over 1.8 million sold. Of course, Ralph Nader's book Unsafe at Any Speed kind of poisoned the well, even if the poor safety reputation wasn't entirely deserved. The Fiero on the other hand only lasted for a few model years before shuffling off, but it eventually got its own performance boost with the V6 version and rather attractive GT models. Check them both out in the video and tell us in Comments which you want in your garage.

Gordon Murray, F1-driven production and .. the Pontiac Fiero

Gordon Murray's design and engineering chops are unquestionable. But does his carmaking approach owe something to the short-lived Pontiac Fiero, a scrappy little car program that emerged from GM against serious resistance? Murray had a Formula One career that ran from 1969 to 1991, with stints at Brabham ('69 to '86) and McLaren ('87-'91), that resulted in several shelves' worth of trophies for the cars he was instrumental in designing. He moved on to McLaren Cars, the consumer side of things, where, during his tenure from 1991 to 2004, he helped design the McLaren F1 and the Mercedes-Benz SLR McLaren, two cars that took learnings from his two decades in Formula One. What do all of these cars have in common? Three things: They are light. They were built in limited numbers. And they were (and are) exceedingly expensive—when the McLaren F1 debuted in 1994, it stickered at $815,000. Murray went on to establish Gordon Murray Design in 2007. GMD has created some interesting concept vehicles, such as the diminutive T.25 city car (94.5 inches long, 51.1 inches wide and 55.1 inches high), and the OX, a lightweight truck for the developing world that packs like an IKEA shelf and is working toward realization through a worthy crowdfunding campaign established by the Global Vehicle Trust. Now he has created a vehicle manufacturing company, Gordon Murray Automotive, that will use manufacturing methods that he developed under the moniker "iStream." Unlike a unibody, there are the "iFrame," a cage-like construction made with metallic components, and the "iPanels," which are composite. The panels aren't simply a decorative skin; they actually provide structure to the vehicle. Presumably this has something of the F1 monocoque about it. Going back to the three elements, (1) this arrangement results in a vehicle that can be comparatively light; (2) Murray has indicated that his manufacturing company will be doing limited-run production; and (3) to launch Gordon Murray Automotive they are going to be building a flagship model, about which Murray said, "With our first new car, we will demonstrate a return to the design and engineering principles that have made the McLaren F1 such an icon." Which seems to imply that it will be on the pricey side. According to the company's verbiage, "iStream forges an entirely new production method that defies conventionality with its Formula One-derived construction and materials technologies." It also sounds a whole lot like ...