1973 Pontiac Firebird 350 Automatic 2-door Coupe on 2040-cars

Auto blog

Junkyard Gem: 1992 Pontiac Firebird

Last spring, this series featured a 1992 Chevrolet Camaro RS in a Northern California junkyard, an example of the final model year for the highly successful third-generation GM F-Body. On a later visit to that yard, I spotted the Pontiac sibling to that car, a Firebird that was born the same year at the same Southern California factory. When the Chevrolet Division introduced the first Camaro as a 1967 model, the Pontiac Division got its own version of the F-Body called the Firebird. While the two cars were built on the same chassis and looked very similar, the first-generation Camaros got Chevrolet engines while their Firebird colleagues got Pontiac engines (including the innovative SOHC straight-six). The 1970-1981 second-generation Firebirds still had some Pontiac-only engines, but Chevrolet and Oldsmobile power crept under some hoods during that period. The third-generation Firebirds first appeared as 1982 models, and they drew from near-identical stockpiles of GM running gear (including the distinctly agricultural Iron Duke four-banger, which could be considered a Pontiac-derived engine). When the Camaro got the axe after 2002, the Firebird's neck was put on the same chopping block. When the Camaro returned for 2010, the Pontiac brand was sputtering to an agonized halt during its final year and there was no chance of the Firebird's return. This car is a fairly ordinary coupe, though it does have the mid-grade 205-horsepower 5.0-liter Chevrolet small-block V8 instead of the base 140-horse 3.1-liter V6. A 5.7-liter small-block was available as well. A five-speed manual transmission was base equipment, but few Americans wanted a three-pedal setup by the early 1990s. This car has the optional four-speed automatic. The MSRP with 5.0 engine, automatic transmission and air conditioning (which this car has) started at $14,304. That's about $31,868 in 2023 dollars. It was built at Van Nuys Assembly in the San Fernando Valley of Los Angeles County. By the dawn of the 1990s, the Camaros and Firebirds made at Van Nuys Assembly had become known as the worst-built GM cars made in North America, and the plant was shut down forever soon after this car was built. Today, a shopping mall lives where the factory once stood. This car managed to drive more than 150,000 miles during its life, so it beat the odds. The thrid-gen F-Body was pretty antiquated by the early 1990s, but the fourth-gen cars handled better and looked up-to-date for the era.

General Motors Recall List

It seems General Motors can't go more than a few weeks without issuing a major recall. Since the initial ignition lock recall on February 10, over 25 million vehicles have been recalled for defects. It seems General Motors can't go more than a few weeks without issuing a major recall. Since the initial ignition lock recall on February 10, over 25 million vehicles have been recalled for defects. We used the National Highway Traffic Safety Administration recall list to compile a snapshot of all the GM vehicles recalled in the last two months. NHTSA also provides a search engine that allows owners to search for recalls on their vehicle. An automotive company must do everything in their power to notify its customers when a recall is issued on a vehicle. If you own any of the following vehicles and you have questions regarding your car, you can contact Chevrolet at 1-866-694-6546, GMC at 1-866-996-9463, Buick at 1-800-521-7300 and Cadillac at 1-866-982-2339. Or check out General Motor's recall site. Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153) or go to www.safercar.gov. Here's a brief summery of the other vehicles currently under recall: July 26 – 414,333 cars affected NHTSA Campaign Number: 14V447000 Models under recall: Certain model year 2011-2012 Buick LaCrosse, Regal and Chevrolet Camaro, as well as certain 2010-2012 Cadillac SRX, Chevrolet Equinox and GMC Terrain vehicles, equipped with power height adjustable driver and passenger seats. Problem: In the affected vehicles, the bolt that secures the driver's and passenger's power front seat height adjuster may fall out causing the seat to drop suddenly to the lowest vertical position. Consequence: If the driver's seat unexpectedly drops, the distraction and altered seat position may affect the drivers' control of the vehicle, increasing the risk of a crash. Solution: Dealers will replace the height adjuster shoulder bolts, free of charge. July 14 – 16,939 cars affected NHTSA Campaign Number: 14V341000 Models under recall: Certain model year 2011 Cadillac CTS vehicles manufactured October 18, 2010, to June 2, 2011. Problem: In the affected vehicles, vibrations from the drive shaft may cause the vehicle's roll over sensor to command the roof rail air bags to deploy. Consequence: If the roof rail air bags deploy unexpectedly, there is an increased risk of crash and injury to the occupants.

Gordon Murray, F1-driven production and .. the Pontiac Fiero

Gordon Murray's design and engineering chops are unquestionable. But does his carmaking approach owe something to the short-lived Pontiac Fiero, a scrappy little car program that emerged from GM against serious resistance? Murray had a Formula One career that ran from 1969 to 1991, with stints at Brabham ('69 to '86) and McLaren ('87-'91), that resulted in several shelves' worth of trophies for the cars he was instrumental in designing. He moved on to McLaren Cars, the consumer side of things, where, during his tenure from 1991 to 2004, he helped design the McLaren F1 and the Mercedes-Benz SLR McLaren, two cars that took learnings from his two decades in Formula One. What do all of these cars have in common? Three things: They are light. They were built in limited numbers. And they were (and are) exceedingly expensive—when the McLaren F1 debuted in 1994, it stickered at $815,000. Murray went on to establish Gordon Murray Design in 2007. GMD has created some interesting concept vehicles, such as the diminutive T.25 city car (94.5 inches long, 51.1 inches wide and 55.1 inches high), and the OX, a lightweight truck for the developing world that packs like an IKEA shelf and is working toward realization through a worthy crowdfunding campaign established by the Global Vehicle Trust. Now he has created a vehicle manufacturing company, Gordon Murray Automotive, that will use manufacturing methods that he developed under the moniker "iStream." Unlike a unibody, there are the "iFrame," a cage-like construction made with metallic components, and the "iPanels," which are composite. The panels aren't simply a decorative skin; they actually provide structure to the vehicle. Presumably this has something of the F1 monocoque about it. Going back to the three elements, (1) this arrangement results in a vehicle that can be comparatively light; (2) Murray has indicated that his manufacturing company will be doing limited-run production; and (3) to launch Gordon Murray Automotive they are going to be building a flagship model, about which Murray said, "With our first new car, we will demonstrate a return to the design and engineering principles that have made the McLaren F1 such an icon." Which seems to imply that it will be on the pricey side. According to the company's verbiage, "iStream forges an entirely new production method that defies conventionality with its Formula One-derived construction and materials technologies." It also sounds a whole lot like ...