2024 Nissan Frontier Pro-x on 2040-cars
Engine:3.8L DI DOHC 24V V6
For Sale By:Dealer
Fuel Type:Gasoline
Transmission:Automatic
Vehicle Title:Clean
VIN (Vehicle Identification Number): 1N6ED1EJ1RN664547
Mileage: 5
Drive Type: RWD
Exterior Color: Green
Interior Color: Gray
Make: Nissan
Manufacturer Exterior Color: Tactical Green Metallic
Manufacturer Interior Color: Steel
Model: Frontier
Number of Cylinders: 6
Number of Doors: 4 Doors
Sub Model: 4x2 PRO-X 4dr Crew Cab 5 ft. SB
Trim: PRO-X
Nissan Frontier for Sale
- 2024 nissan frontier sv(US $39,320.00)
- 2016 nissan frontier desert runner pickup 4d 5 ft(US $21,495.00)
- 2021 nissan frontier sv(US $22,241.00)
- 2024 nissan frontier pro-x(US $40,800.00)
- 2019 nissan frontier sv(US $24,950.00)
- 2022 nissan frontier s(US $24,600.00)
Auto blog
Nissan recalls nearly 20,000 NV vans over gearshift issue
Tue, 26 Mar 2013Nissan is recalling 18,800 NV vans built between December 20, 2010 and January 4, 2013. Certain 2012 and 2013 models equipped with a steering-column-mounted transmission shift levers may have been built with improperly installed shift mechanisms.
If the NV's gear selector plate lock clip wasn't installed correctly, normal road vibration could result in a gear position indicator that does not match the actual gear selection. As a result, when the driver selects 'park,' the transmission could still be in gear or in neutral, and roll away. The National Highway Traffic Safety Administration says this condition greatly increased the risk of accident and injury.
Nissan will inspect the gear selector lock clip and replace the part if necessary free of charge. Owners can expect to be notified once the recall campaign begins on April 8, 2013. Read the full recall notice below for more information.
Nissan expands, shrinks Leaf recall for missing weld points
Thu, May 22 2014Chalk this one up to the quirks of the English language. The other day, we had a post on the recall of a small number of 2014 Nissan Leaf EVs that were missing weld spots. The official bulletin from the National Highway Traffic Safety Administration said that "any vehicle missing welds will be replaced, free of charge." We read that as saying that the welds would be replaced, but in fact it's the cars themselves that will be swapped out. NHTSA said that 211 Leafs were potentially involved in this recall, but we heard from Brian Brockman, Nissan's senior manager of corporate communications, that Nissan is actually looking at, "approximately 276" vehicles. More importantly, Brockman clarified that, "If a vehicle is found to be missing the welds, the entire vehicle will be replaced." NHTSA documents on Inside EVs show that Nissan expects just 0.65 percent of those Leafs will need to be replaced. Brockman wouldn't say exactly how many cars Nissan thinks are affected, but 0.65 percent of 276 is just 1.8 vehicles. Brockman did say that, "you'd be correct to say that we expect the number to be very low." Read Nissan's full statement below. Nissan is conducting a Voluntary Recall Campaign on approximately 276 MY2014 LEAF vehicles to inspect the front member assembly welds. Due to an isolated supplier process error that has been corrected, a small number of vehicles within a subset of MY2014 LEAF vehicles manufactured during a two-week period may have front frame member assembly components that were not welded to proper specification. This can affect crash performance. Within the next few weeks, affected LEAF owners will be asked to bring their vehicle to a certified Nissan LEAF dealer for an inspection. If the vehicle is determined to be affected, Nissan will provide owners with a brand new replacement vehicle at no additional cost. A loaner vehicle will be provided during the vehicle exchange process. It is anticipated that only a handful of retailed vehicles are affected by the weld issue and require vehicle replacement. Nissan is committed to a high level of customer service and satisfaction and is working with its dealers to provide an outstanding ownership experience to Nissan LEAF owners.
Nissan gives us the business on the art of clay modeling
Sat, 06 Apr 2013The team from The Dashboard recently stopped by the Nissan Technical Center in Japan for a look at what exactly goes into creating a full-scale clay model. While automakers have been using clay bucks for decades, designers and engineers are now combining computer renderings and hand-sculpted clay models to determine how a new vehicle will look in our world. Engineers use specially formulated clay kept warm in an oven to bring the body panels to life. They then coat the clay in a thin plastic film to add body color for the final look.
By the time everything is said and done, workers may have hundreds of hours in the model's creation. So, what happens when the company no longer needs the buck? They get scrapped. Someone comes in and dismantles the whole creation. We presume that action is set to the wailing tears of everyone who had a hand in building the model. Check out the video below for a closer look.