2013 Nissan Platinum Reserve on 2040-cars

Auto blog

Infiniti's new VC-T changes the rules of small turbocharged engines

The upcoming Infiniti QX50 crossover does not get our pulse racing, no matter how shapely the QX Sport Inspiration concept that previews it may be. No midsize SUV does, to be fair. But it has something special under the hood – the world's first production variable-compression-ratio engine. That means the QX50's 2.0-liter turbo four, which makes 268 horsepower and 288 pound-feet of torque, will have up to 27 percent better fuel economy. Here's how it works. The trend of moving to smaller, turbocharged engines carries with it one big falsehood. Under low load when the turbo isn't needed, these engines are less efficient than an equivalent engine without a turbo because of the low compression ratio the turbo requires. That is, if you never need the extra power, you're wasting fuel. Turbocharged (and supercharged) engines use a lower compression ratio to prevent detonation. When you force extra air in a cylinder and mix it with fuel, it's more likely to prematurely go boom. Lowering the compression ratio prevents this problem, but it's less efficient. Infiniti's VC-T promises the best of both worlds, with a compression ratio that ranges from 8.0:1 for high-power turbo needs to a 14.0:1 ratio for fuel-sipping efficiency. At its heart the VC-T engine is a simple idea, but it's complicated to explain. Consider yourself warned. The photo below from Infiniti serves as a good visual overview. For the truly nerdy, this patent application covers the mechanical concept. Instead of having the pistons connected to the crankshaft, Infiniti's engine has a pivot arm with a connection on each end. One end connects to the piston, the other connects to a second lower shaft, which is controlled by an actuator arm. At any given time the engine's pistons move up and down according to the lobes on the crankshaft. But the actuator arm can change the angle of the pivot arm up and down. That is, the pistons still move in the same motion with the same stroke, but phase the entire stroke up or down. Move the pivot up and there's less room at the top, which means a higher compression ratio. Move the pivot down and the compression ratio goes down, too. As an added bonus, the lower shaft eliminates the need for counter-rotating balance shafts. Infiniti says this system works constantly and can vary the compression ratio to any number between 8:1 and 14:1. It also uses electronic variable valve timing on the intake valves to switch into Atkinson-cycle combustion for greater efficiency.

Foreign automakers pay from $38 to $65 per hour to non-union workers

As leaders for the United Auto Workers gather in Detroit for their Special Convention on Collective Bargaining to work out the negotiating stance for this year's new labor agreements with the Detroit 3 automakers, what they most want to do is figure out how to eliminate the two-tier wage scale. However, the lower Tier 2 wage has allowed the domestic automakers to reduce their labor costs, hire more workers, and compete better with their import competition. As it stands, per-hour labor rates including benefits are $58 at General Motors, $57 at Ford, and $48 at Fiat-Chrysler – a reflection of FCA's much greater number of Tier 2 workers. The Center for Automotive Research released a study of labor rates (including benefits) that put numbers to what the imports pay: Mercedes-Benz pays the most, at an average of $65 per hour, Volkswagen pays the least, at $38 per hour, and BMW is just a hair above that at $39 per hour. Among the Detroit competitors, Honda workers earn an average of $49 per hour, at Toyota it's $48 per hour, Nissan is $42 per hour, and Hyundai-Kia pays $41 per hour. The lower import wages are aided by their greater use of temporary workers compared to the domestics. Automotive News says the ten-dollar gap between those foreign camakers and the domestics turns out to about an extra $250 per car in labor, which adds up quickly when you're pumping out many millions of cars. That $250-per-car number is one that, come negotiating time, the Detroit 3 will want to reduce, as the UAW is trying to raise both Tier 1 and Tier 2 wages. Another wrinkle is that the domestic carmakers are considering the wide adoption of a third wage level lower than Tier 2. Some workers who do minor tasks like assembling parts trays kits and battery packs already make less than Tier 2, but the UAW will be quite wary about cementing yet another wage scale at the bottom of the system while it's trying to fight a bigger battle at the top. News Source: Automotive News - sub. req., BloombergImage Credit: AP Photo/Erik Schelzig Earnings/Financials UAW/Unions BMW Chevrolet Fiat Ford GM Honda Hyundai Kia Mercedes-Benz Nissan Toyota Volkswagen labor wages collective bargaining labor costs

Nissan BladeGlider Concept shows its inner DeltaWing

Just like the DeltaWing and ZEOD RC racecars, it takes seeing the Nissan BladeGlider concept live to get a true appreciation for its design. But that doesn't mean it's any less weird. The wedge-shaped, three-seat concept car hit the stage today at the Tokyo Motor Show, and Nissan says the car is an "exploratory prototype" for a future production model.
The BladeGlider is defined by its design with front wheels that are just about three feet apart, while the rear has a more conventional track. Opening the scissor doors reveals a center driving position flanked by two passenger seats with a cockpit-inspired design. Although no power figures were revealed for the conceptual vehicle, Nissan does say that the BladeGlider is an all-electric vehicle with its battery pack mounted toward the rear of the car helping to provide a 30/70 weight distribution front to rear.
Check out our live images of the BladeGlider as well as the Nissan press release below.