Mercury Grand Marquis Gs Sedan 4-door 4.6l - 2003 on 2040-cars

Auto blog

Ford recalling 370,000 Crown Vic, Grand Marquis and Town Car models

The Detroit News is reporting that Ford will recall some 370,000 Crown Victoria (pictured), Mercury Grand Marquis and Lincoln Town Car vehicles from model years 2005 through 2011, for an issue regarding the lower intermediate steering shaft. 355,000 of the vehicles in question were sold in the US, with the other 15,000 sold in Canada.
The report indicates that corrosion of the lower intermediate steering shaft could cause a "loss of steering," presumably because of a partial or complete failure of the part. The report points out the dealers will inspect and replace the offending steering component for recalled cars, and may also secure a lower steering column bearing and replace the upper intermediate steering shaft as needed. The company is unaware of any reports of the faulty part causing any accidents or injuries.
Ford helpfully lists states in which corrosion is more likely to have taken place, mostly in the Snow Belt, as you might guess. Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, Wisconsin, West Virginia, and the District of Columbia are listed.

Ford finally issues recall for 230K minivans over rust problems

The rust issue in the rear wheel wells of 2004-2007 Ford Freestar and Mercury Monterey minivans has finally led to a recall. The National Highway Traffic Safety Administration began an investigation into the matter in 2011, said investigation being upgraded to an engineering analysis a year later while NHTSA tried to figure out how many model years should be included in the assessment.
Ford has decided to recall all of the 230,000 minivans potentially affected, namely those sold in salt-belt states and countries like Canada. The excess rust in the rear wheel wells was also able to prevent the third-row seats from locking to the floor of the minivan. To repair the problem, owners can take their minivans to dealers, and the dealers will place new panels in the wheel wells, replace the third-row seat mounting brackets and relocate the latches to an area away from any corrosion.
Ford says it will begin notifying owners during the last week of March.

Ringbrothers shows off Coyote-powered 1968 Mercury Cougar

We'll openly admit that not every SEMA build is our cup of tea. But this? A tastefully resto-modded 1968 Mercury Cougar with a 460-horsepower Ford Mustang V8? Yeah, this is right in our wheelhouse. Sadly, there was no in-pwerson SEMA show in 2020, so we missed out on gems like this one. SEMA or no SEMA, the aftermarket carries on, and co-owners Jim and Mike Ring of Ringbrothers (get it?) saw no reason to let their time and effort go to waste.  When they're not building wild customs (see: 1,100-horsepower 1972 AMC Javelin AMX) or more subtle showcases (such as this Cougar or their 1971 K5 Chevy Blazer build from 2018), the folks at Ringbrothers crank out factory reproduction parts, whether for old-fashioned restoration or modification purposes. While '60s muscle cars are recurring build subjects for the two, the Cougar was the first of its kind they tackled.  Keeping it in the family, Ringbrothers sourced a Ford 5.0-liter "Coyote" V8 and a 10-Speed Automatic (lifted from an F-150 Raptor, incidentally) for the build. They didn't stop with the driveline, of course. The suspension was overhauled with a little help from DSE and a set of HRE Series C1 C103 Forged 3-Piece wheels were thrown over upgraded brakes.  "We put our heart into each car we build, and this Cougar is no exception," Jim said. "The finished product is mild and classy, yet any enthusiast instantly knows it's not stock. I imagine this is what Mercury designers would have come up with if they were building the Cougar today." "While we couldn't bring the car to the SEMA Show, we hope it can be shown to the public soon," Mike said. "We had never done a Cougar before, so this was a fun build. I love working with new shapes and coming up with new ideas." There's plenty to appreciate about this Cougar apart from the mechanicals, too. The finish is Augusta Green Metallic (courtesy of BASF), which was a factory color in 1968. You may know it by another name: Highland Green. There are a few custom exterior touches, but they're quite subtle and styled to be period-correct. The interior was also restored and updated, and it's where you'll find the only thing we're not fond of: that big, fat truck shifter. Gearbox choices notwithstanding, it's a bit of an eyesore. But considering how gorgeous the rest is, we'll give it a pass.  Related Video: