Light Blue Gray Interior Very Clean Carfax One Owner on 2040-cars

Auto blog

NHTSA and Ford investigating steering issues in Crown Vic, Grand Marquis and Marauder

There may be more steering woes for the Ford Crown Victoria. The National Highway Traffic Safety Administration has opened a preliminary evaluation into the Crown Vic and Mercury Grand Marquis from the 2004 to 2007 model years and the Mercury Marauder for the 2004 and 2005 model years because the steering shaft can jam. The issue could potentially affect an estimated 500,000 vehicles.
According to the regulator, there is a possibility that the driver's side heat shield for the exhaust manifold can rust, dislodge, and then wedge into the steering shaft. If this occurs, it leads to a situation where the driver can no longer control the car.
NHTSA has received five complaints of this happening, including one alleged case with an injury. In that situation, the car was driving onto the highway, lost control and rolled over. One occupant was hurt in the accident.

Ford recalls 600,000 older-model sedans for braking issue

Ford is recalling 600,166 older-model Ford, Lincoln and Mercury vehicles over an issue that could affect braking and increase the risk of a crash. The safety recall covers certain Ford Fusion, Mercury Milan and Lincoln MKZ sedans from the 2006 through 2010 model years that were built at Ford’s Hermosillo Assembly Plant in Mexico between Feb. 22, 2006, and July 15, 2009. Ford says a valve that is normally closed inside the hydraulic control unit may get stuck in the open position or be slow to close, which could make it harder to engage the brakes and increase risk of a crash. Ford says itÂ’s aware of 15 reports of accidents and two injuries possibly related to the issue. Dealers will inspect the hydraulic control unit for signs of the problem and replace it, if necessary. The dealers will pressure-flush the system with brake fluid and replace the reservoir cap with a new one. Ford is also issuing a small recall of 33 of its 2020 F-150 trucks in the U.S. and 51 in Canada over potentially damaged spare tires. It says the bead area on the tires may have been damaged when it was mounted onto the wheel assembly, leaving it vulnerable to corrosion, separation of the bead wire and ultimately a rapid loss of air pressure and detachment from the wheel. Dealers will replace the spare tire. Affected vehicles were built at the Dearborn Truck Plant from Nov. 10-21 of this year.

Ringbrothers shows off Coyote-powered 1968 Mercury Cougar

We'll openly admit that not every SEMA build is our cup of tea. But this? A tastefully resto-modded 1968 Mercury Cougar with a 460-horsepower Ford Mustang V8? Yeah, this is right in our wheelhouse. Sadly, there was no in-pwerson SEMA show in 2020, so we missed out on gems like this one. SEMA or no SEMA, the aftermarket carries on, and co-owners Jim and Mike Ring of Ringbrothers (get it?) saw no reason to let their time and effort go to waste.  When they're not building wild customs (see: 1,100-horsepower 1972 AMC Javelin AMX) or more subtle showcases (such as this Cougar or their 1971 K5 Chevy Blazer build from 2018), the folks at Ringbrothers crank out factory reproduction parts, whether for old-fashioned restoration or modification purposes. While '60s muscle cars are recurring build subjects for the two, the Cougar was the first of its kind they tackled.  Keeping it in the family, Ringbrothers sourced a Ford 5.0-liter "Coyote" V8 and a 10-Speed Automatic (lifted from an F-150 Raptor, incidentally) for the build. They didn't stop with the driveline, of course. The suspension was overhauled with a little help from DSE and a set of HRE Series C1 C103 Forged 3-Piece wheels were thrown over upgraded brakes.  "We put our heart into each car we build, and this Cougar is no exception," Jim said. "The finished product is mild and classy, yet any enthusiast instantly knows it's not stock. I imagine this is what Mercury designers would have come up with if they were building the Cougar today." "While we couldn't bring the car to the SEMA Show, we hope it can be shown to the public soon," Mike said. "We had never done a Cougar before, so this was a fun build. I love working with new shapes and coming up with new ideas." There's plenty to appreciate about this Cougar apart from the mechanicals, too. The finish is Augusta Green Metallic (courtesy of BASF), which was a factory color in 1968. You may know it by another name: Highland Green. There are a few custom exterior touches, but they're quite subtle and styled to be period-correct. The interior was also restored and updated, and it's where you'll find the only thing we're not fond of: that big, fat truck shifter. Gearbox choices notwithstanding, it's a bit of an eyesore. But considering how gorgeous the rest is, we'll give it a pass.  Related Video: